Tandem solar cells that pair silicon with a metal halide perovskite are a promising option for surpassing the single-cell efficiency limit. We report a monolithic perovskite/silicon tandem with a certified power conversion efficiency of 29.15%. The perovskite absorber, with a bandgap of 1.68 electron volts, remained phase-stable under illumination through a combination of fast hole extraction and minimized nonradiative recombination at the hole-selective interface. These features were made possible by a self-assembled, methyl-substituted carbazole monolayer as the hole-selective layer in the perovskite cell. The accelerated hole extraction was linked to a low ideality factor of 1.26 and single-junction fill factors of up to 84%, while enabling a tandem open-circuit voltage of as high as 1.92 volts. In air, without encapsulation, a tandem retained 95% of its initial efficiency after 300 hours of operation.

We introduce new hole-selective contacts for next-generation perovskite photovoltaics and point to design paths for molecular engineering of perfect interfaces.

The unprecedented emergence of perovskite‐based solar cells (PSCs) has been accompanied by an intensive search of suitable materials for charge‐selective contacts. For the first time a hole‐transporting self‐assembled monolayer (SAM) as the dopant‐free hole‐selective contact in p–i–n PSCs is used and a power conversion efficiency of up to 17.8% with average fill factor close to 80% and undetectable parasitic absorption is demonstrated. SAM formation is achieved by simply immersing the substrate into a solution of a novel molecule V1036 that binds to the indium tin oxide surface due to its phosphonic anchoring group. The SAM and its modifications are further characterized by Fourier‐transform infrared and vibrational sum‐frequency generation spectroscopy. In addition, photoelectron spectroscopy in air is used for measuring the ionization potential of the studied SAMs. This novel approach is also suitable for achieving a conformal coverage of large‐area and/or textured substrates with minimal material consumption and can potentially be extended to serve as a model system for substrate‐based perovskite nucleation and passivation control. Further gains in efficiency can be expected upon SAM optimization by means of molecular and compositional engineering.

Dominating loss mechanisms were identified at hole-selective buried interfaces engineered with carbazole-based self-assembled monolayers between a metal halide perovskite absorber and a conductive metal oxide. The analysis of surface photovoltage transients with a minimalistic kinetic model allowed for the extraction of interfacial electron trap densities and hole transfer rates and their correlation with open-circuit voltages and fill factors of the corresponding highefficiency solar cells is demonstrated.

The small-molecule-based hole-transporting material methoxydiphenylamine-substituted carbazole was synthesized and incorporated into a CH3NH3PbI3 perovskite solar cell, which displayed a power conversion efficiency of 16.91%, the second highest conversion efficiency after that of Spiro-OMeTAD. The investigated hole-transporting material was synthesized in two steps from commercially available and relatively inexpensive starting reagents. Various electro-optical measurements (UV/Vis, IV, thin-film conductivity, hole mobility, DSC, TGA, ionization potential) have been carried out to characterize the new hole-transporting material.

We demonstrate a monolithic perovskite/CIGS tandem solar cell with a certified power conversion efficiency (PCE) of 24.2%. The tandem solar cell still exhibits photocurrent mismatch between the subcells; thus optical simulations are used to determine the optimal device stack. Results reveal a high optical potential with the optimized device reaching a short-circuit current density of 19.9 mA cm −2 and 32% PCE based on semiempirical material properties. To evaluate its energy yield, we first determine the CIGS temperature coefficient, which is at −0.38% K −1 notably higher than the one from the perovskite subcell (−0.22% K −1 ), favoring perovskite in the field operation at elevated cell temperatures. Both single-junction cells, however, are significantly outperformed by the combined tandem device. The enhancement in energy output is more than 50% in the case of CIGS single-junction device. The results demonstrate the high potential of perovskite/CIGS tandem solar cells, for which we describe optical guidelines toward 30% PCE.

Self-assembled monolayers (SAMs) based on Br-2PACz ([2-(3,6dibromo-9H-carbazol-9-yl)ethyl]phosphonic acid) 2PACz ethyl]phosphonic acid) and ethyl]phosphonic acid) molecules were investigated as hole-extracting interlayers in organic photovoltaics (OPVs). The highest occupied molecular orbital (HOMO) energies of these SAMs were measured at À 6.01 and À 5.30 eV for Br-2PACz and MeO-2PACz, respectively, and found to induce significant changes in the work function (WF) of indium-tin-oxide (ITO) electrodes upon chemical functionalization. OPV cells based on PM6 (poly [(2,6-(4,8-bis(5-(2-ethylhexyl-3- ([6,6]-phenyl-C71-bu-tyric acid methyl ester) using ITO/Br-2PACz anodes exhibited a maximum power conversion efficiency (PCE) of 18.4 %, outperforming devices with ITO/MeO-2PACz (14.5 %) and ITO/poly (3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PE-DOT : PSS) (17.5 %). The higher PCE was found to originate from the much higher WF of ITO/Br-2PACz (À 5.81 eV) compared to ITO/MeO-2PACz (4.58 eV) and ITO/PEDOT : PSS (4.9 eV), resulting in lower interface resistance, improved hole transport/extraction, lower trap-assisted recombination, and longer carrier lifetimes. Importantly, the ITO/Br-2PACz electrode was chemically stable, and after removal of the SAM it could be recycled and reused to construct fresh OPVs with equally impressive performance.

Perovskite solar cells (PSC) have shown that under laboratory conditions they can compete with established photovoltaic technologies. However, controlled laboratory measurements usually performed do not fully resemble operational conditions and field testing outdoors, with day‐night cycles, changing irradiance and temperature. In this contribution, the performance of PSCs in the rooftop field test, exposed to real weather conditions is evaluated. The 1 cm2 single‐junction devices, with an initial average power conversion efficiency of 18.5% are tracked outdoors in maximum power point over several weeks. In parallel, irradiance and air temperature are recorded, allowing us to correlate outside factors with generated power. To get more insight into outdoor device performance, a comprehensive set of laboratory measurements under different light intensities (10% to 120% of AM1.5) and temperatures is performed. From these results, a low power temperature coefficient of −0.17% K−1 is extracted in the temperature range between 25 and 85 °C. By incorporating these temperature‐ and light‐dependent PV parameters into the energy yield model, it is possible to correctly predict the generated energy of the devices, thus validating the energy yield model. In addition, degradation of the tested devices can be tracked precisely from the difference between measured and modelled power.