One of the most important features of striated cardiac muscle is the excitability that turns on the excitation-contraction coupling cycle, resulting in the heart blood pumping function. The function of the heart pump may be impaired by events such as myocardial infarction, the consequence of coronary artery thrombosis due to blood clots or plaques. This results in the death of billions of cardiomyocytes, the formation of scar tissue, and consequently impaired contractility. A whole heart transplant remains the gold standard so far and the current pharmacological approaches tend to stop further myocardium deterioration, but this is not a long-term solution. Electrically conductive, scaffold-based cardiac tissue engineering provides a promising solution to repair the injured myocardium. The non-conductive component of the scaffold provides a biocompatible microenvironment to the cultured cells while the conductive component improves intercellular coupling as well as electrical signal propagation through the scar tissue when implanted at the infarcted site. The in vivo electrical coupling of the cells leads to a better regeneration of the infarcted myocardium, reducing arrhythmias, QRS/QT intervals, and scar size and promoting cardiac cell maturation. This review presents the emerging applications of intrinsically conductive polymers in cardiac tissue engineering to repair post-ischemic myocardial insult.

Failure of tissues and organs resulting from degenerative diseases or trauma has caused huge economic and health concerns around the world. Tissue engineering represents the only possibility to revert this scenario owing to its potential to regenerate or replace damaged tissues and organs. In a regeneration strategy, biomaterials play a key role promoting new tissue formation by providing adequate space for cell accommodation and appropriate biochemical and biophysical cues to support cell proliferation and differentiation. Among other physical cues, the architectural features of the biomaterial as a kind of instructive stimuli can influence cellular behaviors and guide cells towards a specific tissue organization. Thus, the optimization of biomaterial micro/nano architecture, through different manufacturing techniques, is a crucial strategy for a successful regenerative therapy. Over the last decades, many micro/nanostructured biomaterials have been developed to mimic the defined structure of ECM of various soft and hard tissues. This review intends to provide an overview of the relevant studies on micro/nanostructured scaffolds created for soft and hard tissue regeneration and highlights their biological effects, with a particular focus on striated muscle, cartilage, and bone tissue engineering applications.

Electrically conductive scaffolds, mimicking the unique directional alignment of muscle fibers in the myocardium, are fabricated using the 3D printing micro-stereolithography technique. Polyethylene glycol diacrylate (photo-sensitive polymer), Irgacure 819 (photo-initiator), curcumin (dye) and polyaniline (conductive polymer) are blended to make the conductive ink that is crosslinked using free radical photo-polymerization reaction. Curcumin acts as a liquid filter and prevents light from penetrating deep into the photo-sensitive solution and plays a central role in the 3D printing process. The obtained scaffolds demonstrate well defined morphology with an average pore size of 300 ± 15 μm and semi-conducting properties with a conductivity of ~ 10–6 S/m. Cyclic voltammetry analyses detect the electroactivity and highlight how the electron transfer also involve an ionic diffusion between the polymer and the electrolyte solution. Scaffolds reach their maximum swelling extent 30 min after immersing in the PBS at 37 °C and after 4 weeks they demonstrate a slow hydrolytic degradation rate typical of polyethylene glycol network. Conductive scaffolds display tunable conductivity and provide an optimal environment to the cultured mouse cardiac progenitor cells.

Myocardial infarction (MI) is the consequence of coronary artery thrombosis resulting in ischemia and necrosis of the myocardium. As a result, billions of contractile cardiomyocytes are lost with poor innate regeneration capability. This degenerated tissue is replaced by collagen-rich fibrotic scar tissue as the usual body response to quickly repair the injury. The non-conductive nature of this tissue results in arrhythmias and asynchronous beating leading to total heart failure in the long run due to ventricular remodelling. Traditional pharmacological and assistive device approaches have failed to meet the utmost need for tissue regeneration to repair MI injuries. Engineered heart tissues (EHTs) seem promising alternatives, but their non-conductive nature could not resolve problems such as arrhythmias and asynchronous beating for long term in-vivo applications. The ability of nanotechnology to mimic the nano-bioarchitecture of the extracellular matrix and the potential of cardiac tissue engineering to engineer heart-like tissues makes it a unique combination to develop conductive constructs. Biomaterials blended with conductive nanomaterials could yield conductive constructs (referred to as extrinsically conductive). These cell-laden conductive constructs can alleviate cardiac functions when implanted in-vivo. A succinct review of the most promising applications of nanomaterials in cardiac tissue engineering to repair MI injuries is presented with a focus on extrinsically conductive nanomaterials.

Natural soil can play an important role in the production of geopolymer due to having required aluminosilicate precursors and abundant availability. Numerous aluminosilicate materials have been used in the past for the production of geopolymers but they have some limitations like various ashes can be toxic during handling and processing due to presence of harmful components. The major purpose of this study was to develop geopolymers via cheap and easily available aluminosilicate material like loam type of natural soil. Geopolymer specimens were prepared by mixing natural soil and other required precursors such as sodium silicate and sodium hydroxide through ball milling. After the preparation of mortars via subsequent hydrothermal treatment for 24 hours at 60⁰C, the physical and mechanical properties were evaluated. FTIR analysis showed that geopolymerization reaction occurred in soil-based geopolymer mortars. This was confirmed by detecting some zeolitic phases like Albite/Anorthite in geopolymers. X-ray diffraction analysis also confirmed the presence of these zeolitic phases. The maximum compression strength of 22.70 MPa was achieved for A-75 composition which proved to be an optimum composition in this study which is somehow comparable to the compressive strength of ordinary Portland cement (OPC) mortars.