In this work, strain rate sensitivity was studied for 3D-printed polycarbonate (PC) and thermoplastic polyurethane (TPU) materials. Specimens were fabricated through fused filament fabrication (FFF) additive manufacturing (AM) technology and were tested at various strain rates. The effects of two FFF process parameters, i.e., nozzle temperature and layer thickness, were also investigated. A wide analysis for the tensile strength (MPa), the tensile modulus of elasticity (MPa), the toughness (MJ/m3) and the strain rate sensitivity index ‘m’ was conducted. Additionally, a morphological analysis was conducted using scanning electron microscopy (SEM) on the side and the fracture area of the specimens. Results from the different strain rates for each material were analyzed, in conjunction with the two FFF parameters tested, to determine their effect on the mechanical response of the two materials. PC and TPU materials exhibited similarities regarding their temperature response at different strain rates, while differences in layer height emerged regarding the appropriate choice for the FFF process. Overall, strain rate had a significant effect on the mechanical response of both materials.
Utilization of advanced engineering thermoplastic materials in fused filament fabrication (FFF) 3D printing process is critical in expanding additive manufacturing (AM) applications. Polypropylene (PP) is a widely used thermoplastic material, while silicon dioxide (SiO2) nanoparticles (NPs), which can be found in many living organisms, are commonly employed as fillers in polymers to improve their mechanical properties and processability. In this work, PP/SiO2 nanocomposite filaments at various concentrations were developed following a melt mixing extrusion process, and used for FFF 3D printing of specimens’ characterization according to international standards. Tensile, flexural, impact, microhardness, and dynamic mechanical analysis (DMA) tests were conducted to determine the effect of the nanofiller loading on the mechanical and viscoelastic properties of the polymer matrix. Scanning electron microscopy (SEM), Raman spectroscopy and atomic force microscopy (AFM) were performed for microstructural analysis, and finally melt flow index (MFI) tests were conducted to assess the melt rheological properties. An improvement in the mechanical performance was observed for silica loading up to 2.0 wt.%, while 4.0 wt.% was a potential threshold revealing processability challenges. Overall, PP/SiO2 nanocomposites could be ideal candidates for advanced 3D printing engineering applications towards structural plastic components with enhanced mechanical performance.
During the COVID-19 pandemic, wide use of 3D printing technologies has been enabled. Fused filament fabrication (FFF) is the most widely used technique in 3D printing communities worldwide for the fabrication of medical components such as face shields and respiratory valves. In the current study, the potential of Polyamide 12 (PA12) silver-doped antibacterial nanopowder (AgDANP) nanocomposites is evaluated for everyday FFF usage. Filling loadings of 1.0-2.0-3.0 and 4.0 wt.% were selected for nanocomposite preparation. Mechanical performance analysis was conducted on the basis of tensile, flexural, impact, and Vickers microhardness measurements in FFF 3D-printed specimens. Scanning Electron Microscopy (SEM) images were used for morphology and processing evaluation, as well as thermal performance measurements, conducted by Thermogravimetric Analysis (TGA) tests. Finally, the antibacterial performance was tested using the agar-well diffusion screening method, and the shape effect of the specimens was also investigated. The addition of 2.0 wt.% AgDANPs resulted in an enhancement of approximately 27% for both tensile and flexural stresses, while the antibacterial performance was sufficiently high among the nanocomposites tested. The shape effect exhibited the potential for antibacterial performance at low filling ratios, while the effect was diminished with increasing filler of AgDANPs.
In this study, the dimensional accuracy of parts fabricated with PolyJet 3D Printing Direct process is investigated. An L4 orthogonal array was utilized as the design of experiments, while the process parameters examined are layer thickness, build style and scale. A simple prototype was proposed and specified external and internal dimensions were measured using a digital vernier calliper. Grey-Taguchi method was applied for optimizing all dimensional measurements. The effect of each parameter on dimensional accuracy has been identified using ANOM (Analysis of Means), while ANOVA (Analysis of Variances) has been performed to determine each parameter’s dominance. Additionally, the results of this study were compared with the findings of a previous optimization study in which the usual Taguchi method was used. It was concluded that 16 μm of layer thickness, glossy style and 50% scale provide the optimum dimensional results, while scale is the most important factor.
In this work, for the first time, polyamide 12 (PA12) nanocomposites with binary inclusions in material extrusion (MEX) 3D printing were developed. The aim was to achieve an enhanced mechanical response with the addition of titanium nitride (TiN) and antibacterial performance with the addition of copper (Cu) or cuprous oxide (Cu2O), towards the development of multi-functional nanocomposite materials, exploiting the 3D printing process benefits. The prepared nanocomposites were fully characterized for their mechanical properties. The thermal properties were also investigated. Morphological characterization was performed with atomic force microscopy (AFM) and scanning electron microscopy (SEM). The antibacterial performance was investigated with an agar-well diffusion screening process. Overall, the introduction of these nanofillers induced antibacterial performance in the PA12 matrix materials, while at the same time, the mechanical performance was significantly increased. The results of the study show high potential for expanding the areas in which 3D printing can be used.
The feasibility of joining material extrusion (MEX) 3D-printed acrylonitrile butadiene styrene (ABS) plates with the friction stir welding (FSW) process was investigated herein as a promising topic of hybrid additive manufacturing (HAM). The influence of three process parameters on the mechanical strength of the joints was thoroughly examined and analyzed with a full factorial experimental design and statistical modeling. Hereto, the welding tool pin geometry, travel speed, and rotational speed were investigated. The joint’s efficiency and quality are evaluated through tensile tests and morphological characterization. More specifically, specimens’ areas of particular interest were investigated with stereoscopic, optical, and scanning electron microscopy. Throughout the FSW experimental course, the welding temperature was monitored to evaluate the state of the ABS material during the process. The majority of the welded specimens exhibited increased mechanical strength compared with the respective ones of non-welded 3D printed specimens of the same geometry. Statistical modeling proved that all processing parameters were significant. The feasibility of the FSW process in 3D printed ABS workpieces was confirmed, making the FSW a cost-effective process for joining 3D printing parts, further expanding the industrial merit of the approach.
The main objective of this study was to investigate the mechanical behavior of 3D printed fiberglass-reinforced nylon honeycomb structures. A Continuous Fiber Fabrication (CFF) 3D printer was used since it makes it possible to lay continuous strands of fibers inside the 3D printed geometries at selected locations across the width in order to optimize the bending behavior. Nylon and nylon/fiberglass honeycomb structures were tested under a three-point bending regime. The microstructure of the filaments and the 3D printed fractured surfaces following bending tests were examined with Scanning Electron Microscopy (SEM). The modulus of the materials was also evaluated using the nanoindentation technique. The behavior of the 3D printed structures was simulated with a Finite Element Model (FEM). The experimental and simulation results demonstrated that 3D printed continuous fiberglass reinforcement is possible to selectively adjust the bending strength of the honeycombs. When glass fibers are located near the top and bottom faces of honeycombs, the bending strength is maximized.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.