The ability of large grain, REBa2Cu3O7- [(RE)BCO; RE = rare earth] bulk superconductors to trap magnetic field is determined by their critical current. With high trapped fields, however, bulk samples are subject to a relatively large Lorentz force, and their performance is limited primarily by their tensile strength. Consequently, sample reinforcement is the key to performance improvement in these technologically important materials. In this work, we report a trapped field of 17.6 T, the largest reported to date, in a stack of two, silver-doped GdBCO superconducting bulk samples, each of diameter 25 mm, fabricated by top-seeded melt growth (TSMG) and reinforced with shrink-fit stainless steel. This sample preparation technique has the advantage of being relatively straightforward and inexpensive to implement and offers the prospect of easy access to portable, high magnetic fields without any requirement for a sustaining current source.

The ability to generate a permanent, stable magnetic field unsupported by an electromotive force is fundamental to a variety of engineering applications. Bulk high temperature superconducting (HTS) materials can trap magnetic fields of magnitude over ten times higher than the maximum field produced by conventional magnets, which is limited practically to rather less than 2 T. In this paper, two large c-axis oriented, single-grain YBCO and GdBCO bulk superconductors are magnetised by the pulsed field magnetisation (PFM) technique at temperatures of 40 and 65 K and the characteristics of the resulting trapped field profile are investigated with a view of magnetising such samples as trapped field magnets (TFMs) in-situ inside a trapped flux-type superconducting electric machine. A comparison is made between the temperatures at which the pulsed magnetic field is applied and the results have strong implications for the optimum operating temperature for TFMs in trapped fluxtype superconducting electric machines. The effects of inhomogeneities, which occur during the growth process of single-grain bulk superconductors, on the trapped field and maximum temperature rise in the sample are modelled numerically using a 3D finite-element model based on the H-formulation and implemented in Comsol Multiphysics 4.3a. The results agree qualitatively with the observed experimental results, in that inhomogeneities act to distort the trapped field profile and reduce the magnitude of the trapped field due to localised heating within the sample and preferential movement and pinning of flux lines around the growth section regions (GSRs) and growth sector boundaries (GSBs), respectively. The modelling framework will allow further investigation of various inhomogeneities that arise during the processing of (RE)BCO bulk superconductors, including inhomogeneous J c distributions and the presence of current-limiting grain boundaries and cracks, and it can be used to assist optimisation of processing and PFM techniques for practical bulk superconductor applications.

Investigating and predicting the magnetization of bulk superconducting materials and developing practical magnetizing techniques is crucial to using them as trapped field magnets (TFMs) in engineering applications. The pulsed field magnetization (PFM) technique is considered to be a compact, mobile and relative inexpensive way to magnetize bulk samples, requiring shorter magnetization times (on the order of milliseconds) and a smaller and less complicated magnetization fixture; however, the trapped field produced by PFM is generally much smaller than that of slower zero field cooling (ZFC) or field cooling (FC) techniques, particularly at lower operating temperatures. In this paper, the PFM of two, standard Ag-containing Gd-Ba-Cu-O samples is carried out using two types of magnetizing coils: 1) a solenoid coil, and 2) a split coil, both of which make use of an iron yoke to enhance the trapped magnetic field. It is shown that a significantly higher trapped field can be achieved using a split coil with an iron yoke, and in order to explain these how this arrangement works in detail, numerical simulations using a 2D axisymmetric finite element method based on the H-formulation are carried to qualitatively reproduce and analyse the magnetization process from both electromagnetic and thermal points of view. It is observed that after the pulse peak significantly less flux exits the bulk when the iron core is present, resulting in a higher peak trapped field, as well as more overall trapped flux, after the magnetization process is complete. The results have important implications for practical applications of bulk superconductors as such a split coil arrangement with an iron yoke could be incorporated into the design of a portable, high magnetic field source/magnet to enhance the available magnetic field or in an axial gap-type bulk superconducting electric machine, where iron can be incorporated into the stator windings to 1) improve the trapped field from the magnetization process, and 2) increase the effective air-gap magnetic field.

No abstract

Abstract

Magnetisation is one of the main barriers to practical use of bulk superconductors as high field magnets. Recently several authors have reported a flux jump effect that allows penetration of magnetic flux into a bulk superconductor during pulsed field magnetisation (PFM) at lower fields than that would be predicted on the basis of the Bean model. We have systematically investigated macroscopic flux jumps in single grain GdBa 2 Cu 3 O 7−δ -Ag (GdBCO-Ag) bulk superconductors with diameters of up to 30 mm when subjected to pulsed magnetic fields. Flux jumps were observed at temperatures between 30 and 77 K and in applied magnetic fields of up to 7 T. The applied pulsed field required to trigger the instability or flux jump field, B j , was determined experimentally and found to increase with decreasing temperature. An extended instability criterion based on a 2D axisymmetric model was used to predict B j at various temperatures and the results are in good agreement with experiments. A significant temperature rise has been measured experimentally during the magnetisation process which indicates that local heat generation due to the sharp rise of the applied field in the PFM process is the primary cause of the flux jumps. The experimental results suggest further that the critical current density reduces to almost zero in the warm part of the sample during the short period of non-equilibrium. A peak trapped field of 4.1 T at the surface and 5.3 T between a stack of two GdBCO-Ag bulk superconductors was achieved at 30 K by means of an optimised two-step pulse sequence with the assistance of the flux jumps, which is extremely promising for potential applications of these technologically important materials.

Single-grain, (RE)−Ba−Cu−O [(RE)BCO)]bulk high-temperature superconductors have significant potential for application as trapped field magnets in a range of engineering devices. However, it is not trivial to fabricate single grains of (RE)BCO due to the complexity of the growth process, especially when the sample diameter exceeds 25 mm. In particular, difficulties associated with the seed crystal can lead to poor grain growth or to complete growth failure. We have employed an optimized buffer technique, which was determined by optimizing targeted critical parameters of the buffer pellet, including the choice of the buffer pellet composition and its aspect ratio, for the reliable fabrication of large, single grains of (RE)BCO. Potential candidates for the buffer pellet composition have been identified to yield successful grain growth and good superconducting properties. The optimum aspect ratio of the buffer pellet was also determined as part of this study. The optimized buffer pellet capped with the seed crystal has been demonstrated to work effectively as an efficient seed crystal and to aid significantly the growth of the Y-123 phase. We show that this optimized buffer technique ameliorates problems associated with both interfacial stress (commonly occurring at the seed/sample interface) and problems of grain contamination. We have fabricated a 40.8 mm diameter single-grain bulk superconductor and more than 25 single-grain YBCO samples with diameters in the range 25−35 mm by a significantly improved top-seeded melt growth process.

The magnitude of the maximum trapped magnetic field in a bulk, single-grain superconductor is a key performance figure of merit. This is determined, generally, by the magnitude of the critical current density, J c , and the length scale over which it flows. As with all type-II superconductors, J c is related closely to the microstructure of the superconducting material and, in the case of RE–Ba–Cu–O [(RE)BCO, where RE is a rare-earth element or yttrium] single grains, RE2BaCuO5 (RE-211) inclusions in the superconducting REBa2Cu3O7−δ (RE-123) phase matrix are key microstructural features that act effectively as flux pinning centres. Although the distribution of RE-211 in single-grain bulk superconductors has been studied extensively, the variation of J c within a given sample has been much investigated much less thoroughly. A detailed experimental understanding of the variation of J c in these technologically important materials, therefore, is required given the growing popularity and significance of numerical techniques for modelling the behaviour of type-II bulk superconductors. Here we report a systematic investigation of the correlation between Gd-211 particle density and sample porosity, which are microstructural features, and T c and J c in a Gd–Ba–Cu–O bulk, single grain fabricated using a buffer layer and a supply of additional liquid phase. This was performed by cutting the sample into numerous sub-specimens of approximate dimensions 1.8 × 2.8 × 1.5 mm3. We observe that J c decreases with distance from the seed, although more strongly with distance along the c-axis than along the a–b plane. In contrast to what might be expected given the assumed contribution of RE-211 inclusions to flux pinning, we find no evidence of a clear correlation between the local RE-211 precipitate density and local critical current on a length scale of mm. We observe that the porosity of the sample is a more dominant factor in determining the distribution of J c within a single grain.