No abstract

The evaluation of the photocatalysis of visible light activated titanium dioxide employed in hydrogen peroxide (H2O2) was carried using seven H2O2 solutions (3.5 and 35%) and/or methylene blue (MB), with or without light irradiation (LI); the absorbance of MB was the bleaching indicator. Color analysis was performed on bovine teeth (n=12) using two different concentrations of H2O2, 6 and 35% associated with titanium dioxide (TiO2). Data were analyzed with one and two-way ANOVA, and significance level of p<0.05. Solutions containing MB, H2O2 at 3.5 or 35%, and TiO2, followed by LI, showed significant difference when compared with other groups. Greater MB reduction was found in 35% concentration. H2O2 35%+TiO2 gel showed no difference in comparison to control group. All groups for the color analysis assay showed ΔE higher than 3.3. In conclusion, TiO2 and H2O2 association is a promisor alternative for reducing the clinical time of in-office dental bleaching.

No abstract

No abstract

This work has focused on the development of electrospun TiO2 fiber composite photoelectrodes for hydrogen production by water splitting. For comparison, similar photoelectrodes were also developed using commercial TiO2 (Aeroxide P25) nanoparticles (NPs). Dispersions of either fibers or P25 NPs were used to make homogenous TiO2 films on fluorine-doped SnO2 (FTO) glass substrates by a doctor blade (DB) technique. Scanning electron microscopy (SEM) analysis revealed a much lower packing density of the DB fibers, with respect to DB-P25 TiO2 NPs; this was also directly reflected by the higher photocurrent measured for the NPs when irradiating the photoelectrodes at a light intensity of 1.5AM (1 sun, 1000 W/m(2)). For a better comparison of fibers vs. NPs, composite photoelectrodes by dip-coating (onto FTO) TiO2 sol-gel (SG) matrixes containing an equal amount (5 or 20 wt %) of either fibers or P25 NPs were also investigated. It emerged that the photoactivity of the fibers was significantly higher. For composites containing 5 wt % TiO2 fibers, a photocurrent of 0.5 mA/cm(2) (at 0.23 V vs Ag/AgCl) was measured, whereas 5 wt % P25 NPs only provided 0.2 mA/cm(2). When increasing to 20 wt % fibers or NPs, the photocurrent decreased, because of the formation of microcracks in the photoelectrodes, because of the shrinkage of the sol-gel. The high photoactivity of the fiber-based electrodes could be confirmed by incident photon to current efficiency (IPCE) measurements. Remarkably, the IPCE of composites containing 5 wt % fibers was between 35% and 40% in the region of 380-320 nm, and when accounting for transmission/reflection losses, the absorbed photon to current efficiency (APCE) was consistently over 60% between 380 nm and 320 nm. The superior photoactivity is attributed to the enhanced electron transport in the electrospun fibers, with respect to P25 NPs. According to this study, it is clear that the electronic connectivity ensured by the sol-gel also contributes positively to the enhanced photocurrent.

No abstract

N-methylpyrrolidone, previously reported as suitable solvent for suspension of other layered materials, results in the highest concentration among the pure solvents tested in this work; however a simple mixture of 30% of propan-2-ol in water surpasses its performance offering a low cost alternative. An optimal surface tension of 28 mN m(-1) is proposed and the influence of the molecular size of the solvent is also considered. The use of anionic surfactant in water makes feasible the exfoliation of WSe2 in aqueous solutions. The analysis of different exfoliation approaches under same processing conditions permits adequate comparison between different solvent systems and reveal optimal parameters for high yield liquid exfoliation of WSe2.

No abstract