In this study, metal-based biomaterials were functionalized with ascorbic acid (LAA). Two types of substrates were used: austenitic steel 316L and titanium Ti6Al4V. Coatings were prepared with the sol-gel method and applied on metal surfaces using the dip-coating technique. Ascorbic acid was delivered with SiO2-coating at concentrations of 0.1 and 0.4 M. The morphology of the surfaces and coatings was determined using scanning electron microscope (SEM), whereas their elemental composition by SEM-EDX. Immobilization of ascorbic acid in the coatings was confirmed with Raman spectroscopy. The biocompatibility of the materials obtained was tested in vitro using both bone marrow- and adipose-derived mesenchymal stem cells (BMMSC and ADMSC, respectively). Proliferation rate and morphology of cells cultured in the presence of designed biomaterials were monitored after 24, 48, 120 and 168 h of propagation. The results obtained indicated that silica coatings doped with 0.4 M LAA had a positive effect on the proliferation rate of investigated cells, and in some cases on the growth pattern of culture.

The objective of this study was to determine biocompatibility of zirconia-based coatings obtained by the sol-gel method. Two matrices, ZrO2 and SiO2/ZrO2, were created and applied on stainless steel type 316L with dip-coating technique. The morphology and topography of biomaterials' surface were characterized using energy-dispersive X-ray spectroscopy and atomic force microscopy, while chemical composition was analyzed by Raman spectroscopy. Additionally, wettability and surface free energy were characterized. Biocompatibility of obtained biomaterials was evaluated using an in vitro model employing mesenchymal stem cells (MSCs) of adipose and bone marrow origin. Biological analysis included determination of proliferation activity and morphology of MSCs in cultures on synthesized biomaterials. Osteoinductive properties of biomaterials were determined both in non-osteogenic, as well as osteogenic conditions. The results showed that investigated biomaterials exerted different impact on MSCs. Biomaterial with ZrO2 layer was more biocompatible for adipose-derived MSCs, while SiO2/ZrO2 layer promoted proliferation of bone marrow derived MSCs. Moreover, hybrid coating exhibited greater osteoinductive properties than ZrO2 coating, both on cultures with adipose-derived stromal (stem) cells and bone marrow stromal cells. Observed biological effects may result not only from different chemical composition, but also from diverse wettability. The ZrO2 coating was characterized as hydrophobic layer, while SiO2/ZrO2 exhibited hydrophilic properties. The results obtained suggest that behavior of MSCs in response to the biomaterial may vary depending on their origin, therefore we postulate, that screening analysis of implants' biocompatibility, should incorporate model applying both adipose- and bone marrow derived MSCs.

In recent years, much attention has been paid to the development of tissue engineering and regenerative medicine, especially when stem cells of various sources are concerned. In addition to the interest in mesenchymal stem cells isolated from bone marrow, recently more consideration has been given to stem cells isolated from adipose tissue (AdMSCs), due to their less invasive method of collection as well as their ease of isolation and culture. However, the development of regenerative medicine requires both the application of biocompatible material and the stem cells to accelerate the regeneration. In this study, we investigated the morphology, proliferation rate index (PRi), and population doubling time factor of adipose-derived mesenchymal stem cells cultured on non-aqueous sol-gel-derived SiO2, TiO2, and SiO2/TiO2 oxide coatings. The results indicated an increase in PRi of AdMSCs when cultured on to titanium dioxide, suggesting its high attractiveness for AdMSCs. In addition, the proper morphology and the shortest doubling time of AdMSCs were observed when cultured on titanium dioxide coating.

In this paper results of the surface modification of the Ti-15Mo, Ti-13Nb-13Zr, Ti-6Al-7Nb alloys by plasma electrolytic oxidation (PEO) coupled by electrophoretic deposition (EPD) technique were presented. On the porous oxide layers hydroxyapatite (HA) particles were deposited, filled cracks and pores of the coatings. The surfaces of the titanium alloys were modified to enhance their corrosion resistance and bioactivity in biological environment. The influence of voltage, time of the EPD process, and bath composition on hydroxyapatite particles deposition on the porous samples were studied. Microstructure, cross-section, phase composition, surface roughness and wettability of the multilayer coatings were determined. Electrochemical investigations shown, that the titanium alloys surfaces modification improved corrosion resistance of the substrates in Ringer solution. Scratch testing shown that the coatings exhibit good adhesion to the substrate. The coatings formed on the titanium alloys surface were bioactive. After simulated body fluid (SBF) immersion, on all of the samples the apatite crystallized and covered the coatings.

No abstract

The biocompatibility of the bone implants is a crucial factor determining the successful tissue regeneration. The aim of this work was to compare cellular behavior and osteogenic properties of rat adipose-derived multipotent stromal cells (ASCs) and bone marrow multipotent stromal cells (BMSCs) cultured on metallic substrate covered with TiO2 sol-gel-derived nanolayer. The morphology, proliferation rate, and osteogenic differentiation potential of both ASCs and BMSCs propagated on the biomaterials were examined. The potential for osteogenic differentiation of ASCs and BMSCs was determined based on the presence of specific markers of osteogenesis, that is, alkaline phosphatase (ALP), osteopontin (OPN), and osteocalcin (OCL). Additionally, the concentration of calcium and phosphorus in extracellular matrix was determined using energy-dispersive X-ray spectroscopy (SEM-EDX). Obtained results showed that TiO2 layer influenced proliferation activity of ASCs, which manifested by shortening of population doubling time and increase of OPN secretion. However, characteristic features of cells morphology and growth pattern of cultures prompted us to conclude that ultrathin TiO2 layer might also enhance osteodifferentiation of BMSCs. Therefore in our opinion, both populations of MSCs should be used for biological evaluation of biomaterials compatibility, such results may enhance the area of investigations related to regenerative medicine.

No abstract

Silica-based sol-gel coatings have gained attention in bone therapies and orthopedic applications, due to the biocompatibility and bioactivity, including a high potential for the controlled release both in vitro and in vivo. Bioactive materials are created to facilitate the biocompatibility of orthopedic implants. One of the promising alternatives is biomaterials with immobilized drugs. In this study we demonstrated for the first time novel sol-gel-derived silica coatings with active amino groups (SiO2(NH2)) functionalized with a steroid drug-betamethasone, applied to a substrate 316 L using dip coating technique. The presence of betamethasone in functionalized coatings was directly confirmed by Raman spectroscopy and energy-dispersive X-ray spectroscopic analysis. The wettability was evaluated by the sessile drop method, while the surface free energy was estimated based on the contact angles measured. Our results showed a shift in surface properties from hydrophobic to hydrophilic after application of the coatings. We have investigated the morphology, proliferation factor, and the population doubling time of adipose-derived stem cells for biological purposes. Moreover, the analysis of the distribution and localization of cellular microvesicles was performed to evaluate the influence of functionalized surfaces on cellular cytophysiological activity. Increased proliferation and activation of cells, determined by the observations of microvesicles shedding processes, provided evidence of the availability of the drug. Therefore, we conclude that the sol-gel synthesis proposed here allows to improve the metal substrates and can be successfully used for immobilization of betamethasone. This in turn enables the direct delivery of the drug with implanted material into the wound site, and to stimulate the activity of cells to enhance tissue regeneration.