A generalized cyclic steel model characterized by isotropic and kinematic hardening, inelastic buckling in compression and corrosion of rebars in reinforced concrete (RC) structures is presented. The model has been implemented in a fiber code, to perform seismic analyses of RC sections. The model is particularly accurate with respect to experimental cyclic behavior of rebars with buckling in compression when the strain does not exceed 1.5%. Twelve configurations of RC cross sections were selected as case studies for three geometries and different steel arrangements, assumed representative of RC columns or bridge piers (in a suitable scale). Each section was subjected to two groups of cyclic curvature histories representative of severe seismic loads, not far from collapse. Different axial loads and corrosion percentages (no corrosion, moderate, or high) have been selected to perform cyclic parametric analyses. One of the cases was taken from an experimental test on columns, deriving also steel characteristics used in all numerical cases. The results of the comparison among RC sections have been discussed. Numerical results show that the maximum compressive strain for steel rebars is always smaller than 1.5%, therefore the proposed steel model is accurate and represents a valid tool for structural assessment. Corrosion reduces RC section capacity, affecting various rebar mechanical characteristics, in particular buckling behavior.

This study presents the results of a refined numerical investigation meant at understanding the time‐dependent cyclic behavior of reinforced concrete (RC) bridge columns under chlorides‐induced corrosion. The chloride ingress in the cross‐section of the bridge column is simulated, taking into account the effects of temperature, humidity, aging, and corrosion‐induced cover cracking. Once the partial differential equations governing such multiphysics problem are solved through the finite‐element method, the loss of reinforcement steel bars cross‐section is calculated based on the estimated corrosion current density. The nonlinear cyclic response of the RC bridge column under corrosion is, thus, determined by discretizing its cross‐sections into several unidirectional fibers. In particular, the nonlinear modeling of the corroded longitudinal rebars exploits a novel proposal for the estimation of the ultimate strain in tension and also accounts for buckling under compression. A parametric numerical study is finally conducted for a real case study to unfold the role of corrosion pattern and buckling mode of the longitudinal rebars on the time variation of capacity and ductility of RC bridge columns.

This paper discusses the seismic behavior of reinforced concrete (RC) bridge structures, focusing on the shear–flexure interaction phenomena. The assessment of reinforced concrete bridges under seismic action needs the ability to model the effective non-linear response in order to identify the relevant failure modes of the structure. Existing RC bridges have been conceived according to old engineering practices and codes, lacking the implementation of capacity design principles, and therefore can exhibit premature shear failures with a reduction of available strength and ductility. In particular, recent studies have shown that the shear strength can decrease with the increase of flexural damage after the development of plastic hinges and, in some cases, this can cause unexpected shear failures in the plastic branch with a consequent reduction of ductility. The aim of the research is to implement those phenomena in a finite-element analysis. The proposed model consists of a flexure fiber element coupled with a shear and a rotational slip spring. The model has been implemented in the OpenSEES framework and calibrated against experimental data, showing a good ability to capture the overall response.

Road network functionality after an earthquake is a crucial aspect for an already struck community. In particular, bridges are susceptible to earthquake-induced damages and to lengthy restoration works. This may lead to severe and unexpected disruption of traffic. In this paper, a model for the assessment of the seismic resilience of a road network is presented. The proposed model permits us to evaluate the earthquake-induced perturbations to the functionality of a network in terms of transportation capacities, traffic congestion, and travel times due to bridge damages and subsequent restoration interventions. The evolution over time of the functionality of the network is studied by means of a multi-stage approach describing the evolution of the situation in terms of reducing the normal pre-earthquakes transportation capacities. The methodology has been illustrated with reference to a hypothetical case study, a road network composed of 14 nodes and 31 links.

The rehabilitation of reinforced concrete (RC) bridge columns subjected to chloride-induced corrosion is addressed in the present paper. The proposed strategy is based on the replacement of the original external layer made of normalstrength concrete (NSC) with ultra-high performance fiber reinforced concrete (UHPFRC), and it additionally involves the substitution of the existing corroded longitudinal reinforcement with new machined steel rebars. This repair technique aims at restoring strength, stiffness, and ductility of the original column in a short time without altering its cross-section dimensions. Because of the high compactness of the UHPFRC, it also serves at improving its durability. The main contribution of the present work is a numerical investigation carried out in order to identify how the design decisions about the repair strategy influence the behavior of the restored column. The parametric investigation reveals that the length of the zone in which NSC is replaced by UHPFRC as well as the machined index (i.e., ratio between turned and original rebar cross-section area) must be properly selected to make the intervention effective. Numerical results also highlight that the main design issue to deal with is the relocation of the plastic hinge from the repaired zone towards the weak unrepaired part of the column. Practical design recommendations are finally formulated.bridge column, machined steel rebars, pitting corrosion, reinforced concrete, repair, UHPFRC | INTRODUCTIONExposure to corrosive environments is one of the most common and detrimental sources of deterioration in Discussion on this paper must be submitted within two months of the print publication. The discussion will then be published in print, along with the authors' closure, if any, approximately nine months after the print publication.