No abstract

In this study the influence of dialdehyde starch addition on the properties of scaffold based on gelatin and chitosan obtained by freeze-drying method was investigated. In addition, the adhesion and proliferation of human osteosarcoma SaOS-2 cells was examined on obtained scaffolds. Chitosan and gelatin were mixed in different weigh ratios (75/25, 50/50, 25/75) with 1, 2 and 5 wt% addition of dialdehyde starch. The obtained scaffolds were subjected to mechanical testing, infrared spectroscopy, swelling measurements, low-pressure porosimetry and zeta potential measurement. Internal material structures were observed by scanning electron microscopy. The results showed that the cross-linking process occurred after the addition of dialdehyde starch and resulted in increased mechanical strength, swelling properties, zeta potential and porosity of studied materials. Attachment of SaOS-2 cells to all modified materials was better compared to unmodified control and proliferation of these cells was markedly increased on modified scaffolds.

A primary goal in bone tissue engineering is the design of implants that induce controlled, guided, and rapid healing. The events that normally lead to the integration of an implant into bone and determine the performance of the device occur mainly at the tissue-implant interface. Topographical surface modification of a biomaterial might be an efficient tool for inducing stem cell osteogenic differentiation and replace the use of biochemical stimuli. The main goal of this work was to develop micropatterned bioactive silica thin films to induce the osteogenic differentiation of human bone marrow-derived mesenchymal stem cells (hMSCs) only through topographical stimuli. Line and pillar micropatterns were developed by a combination of sol-gel/soft lithography and characterized by scanning electron microscopy, atomic force microscopy, and contact angle measurements. hMSCs were cultured onto the microfabricated thin films and flat control for up to 21 days under basal conditions. The micropatterned groups induced levels of osteogenic differentiation and expression of osteoblast-associated markers higher than those of the flat controls. Via comparison of the micropatterns, the pillars caused a stronger response of the osteogenic differentiation of hMSCs with a higher level of expression of osteoblast-associated markers, ALP activity, and extracellular matrix mineralization after the cells had been cultured for 21 days. These findings suggest that specific microtopographic cues can direct hMSCs toward osteogenic differentiation.

No abstract

The growing demand for better implant aesthetics has led to increased research on the development of all-ceramic dental implants. The use of microtextured coatings with enhanced properties has been presented as a viable way to improve tissue integrability of all-ceramic implants. The aim of this study was to evaluate the effects of different densities of anisotropic microtextured silica thin films, which served as a model coating, on the behavior of human osteoblast-like cells. The differential responses of human osteoblast-like cells to anisotropic silica microtextures with varying densities, produced via a combination of sol-gel and soft lithography processing, were evaluated in terms of alignment, elongation (using fluorescence microscopy), overall cellular activity, and the expression/activity levels of alkaline phosphatase (ALP). Statistical analysis was conducted using one-way ANOVA/Tukey HSD post hoc test. The thin films were thoroughly characterized via scanning electron microscopy/energy dispersive spectroscopy, Fourier transform infrared, and contact angle measurements. Thin film characterization revealed increased nanoscale roughness and reduced wettability on the micropatterned surfaces. Cell culture experiments indicated that the microtextures induced cell alignment, elongation, and guided colonization on the surface. Cells cultured on denser micropatterns exhibited increased metabolic activity (t = 14-21 days). The early expression/activity levels of ALP released into the medium were found to be significantly higher only on the least dense micropattern. These results suggest the possibility that microstructured silica thin films could be used to guide and enhance peri-implant cell/tissue responses, potentially improving tissue integration for metallic and all-ceramic dental implants.

Despite the intensive efforts dedicated to cancer diagnosis and treatment, lung cancer (LCa) remains the leading cause of cancer-related mortality, worldwide. The poor survival rate among lung cancer patients commonly results from diagnosis at late-stage, limitations in characterizing tumor heterogeneity and the lack of non-invasive tools for detection of residual disease and early recurrence. Henceforth, research on liquid biopsies has been increasingly devoted to overcoming these major limitations and improving management of LCa patients. Liquid biopsy is an emerging field that has evolved significantly in recent years due its minimally invasive nature and potential to assess various disease biomarkers. Several strategies for characterization of circulating tumor cells (CTCs) and circulating tumor DNA (ctDNA) have been developed. With the aim of standardizing diagnostic and follow-up practices, microfluidic devices have been introduced to improve biomarkers isolation efficiency and specificity. Nonetheless, implementation of lab-on-a-chip platforms in clinical practice may face some challenges, considering its recent application to liquid biopsies. In this review, recent advances and strategies for the use of liquid biopsies in LCa management are discussed, focusing on high-throughput microfluidic devices applied for CTCs and ctDNA isolation and detection, current clinical validation studies and potential clinical utility.

Dental ceramic implants have shown superior esthetic behavior and the absence of induced allergic disorders when compared to titanium implants. Zirconia may become a potential candidate to be used as an alternative to titanium dental implants if surface modifications are introduced. In this work, bioactive micropatterned silica coatings were produced on zirconia substrates, using a combined methodology of sol–gel processing and soft lithography. The aim of the work was to compare the in vitro behavior of human gingival fibroblasts (HGFs) and human dermal microvascular endothelial cells (HDMECs) on three types of silica-coated zirconia surfaces: flat and micropatterned (with pillars and with parallel grooves). Our results showed that cells had a higher metabolic activity (HGF, HDMEC) and increased gene expression levels of fibroblast-specific protein-1 (FSP-1) and collagen type I (COL I) on surfaces with pillars. Nevertheless, parallel grooved surfaces were able to guide cell growth. Even capillary tube-like networks of HDMEC were oriented according to the surface geometry. Zirconia and silica with different topographies have shown to be blood compatible and silica coating reduced bacteria adhesion. All together, the results indicated that microstructured bioactive coating seems to be an efficient strategy to improve soft tissue integration on zirconia implants, protecting implants from peri-implant inflammation and improving long-term implant stabilization. This new approach of micropatterned silica coating on zirconia substrates can generate promising novel dental implants, with surfaces that provide physical cues to guide cells and enhance their behavior.

No abstract