No abstract

Multicomponent oxide systems 800-Cu-Mg-Fe-O and 800-Cu-Mg-Fe-O-Ce were tested as catalysts of selective catalytic oxidation of ammonia to dinitrogen (NH3-SCO) process. Materials were obtained by calcination of hydrotalcite-like compounds at temperature 800 °C. Some catalysts were doped with cerium by the wet impregnation method. Not only simple oxides, but also complex spinel-like phases were formed during calcination. The influence of chemical composition, especially the occurrence of spinel phases, copper loading and impregnation by cerium, were investigated. Materials were characterized by several techniques: X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), low-temperature nitrogen adsorption (BET), cyclic voltammetry (CV), temperature programmed reduction (H2-TPR), UV-vis diffuse reflectance spectroscopy and scanning electron microscopy (SEM). Examined oxides were found to be active as catalysts of selective catalytic oxidation of ammonia with high selectivity to N2 at temperatures above 300 °C. Catalysts with low copper amounts (up to 12 wt %) impregnated by Ce were slightly more active at lower temperatures (up to 350 °C) than non-impregnated samples. However, when an optimal amount of copper (12 wt %) was used, the presence of cerium did not affect catalytic properties. Copper overloading caused a rearrangement of present phases accompanied by the steep changes in reducibility, specific surface area, direct band gap, crystallinity, dispersion of CuO active phase and Cu2+ accessibility leading to the decrease in catalytic activity.

Exfoliated graphitic carbon nitride (g-C3N4) and two commercially available nanomaterials from titanium dioxide (P25 and CG300) were tested for the photocatalytic degradation of paracetamol (PAR), ibuprofen (IBU), and diclofenac (DIC). Prior to photocatalytic experiments, the nanomaterials were characterized by common methods, such as X-ray diffraction (XRD), UV–VIS diffuse reflectance spectroscopy (DRS), Fourier transformed infrared spectroscopy in attenuated total reflection mode (FTIR–ATR), transmission electron microscopy (TEM), physisorption of nitrogen, and dynamic vapor adsorption (DVS) of water. The sizes and specific surface area (SSA) of the TiO2 nanoparticles were 6 nm and 300 m2·g−1 for CG300 and 21 nm and 50 m2·g−1 for P25. The SSA of g-C3N4 was 140 m2·g−1. All photocatalytic experiments were performed under UV (368 nm), as well as VIS (446 nm) irradiation. TiO2 P25 was the most active photocatalyst under UV irradiation and g-C3N4 was the most active one under VIS irradiation. Photodegradation yields were evaluated by means of high performance liquid chromatography (HPLC) and reaction intermediates were identified using gas chromatography with mass detection (GC–MS). Paracetamol and ibuprofen were totally removed but the intermediates of diclofenac were observed even after 6 h of irradiation. Some intermediates, such as carbazole-1-acetic acid, 2,6-dichloraniline, and hydroxylated derivates of diclofenac were identified. This study showed that g-C3N4 is a promising photocatalyst for the degradation of pharmaceuticals in an aqueous environment, under visible light.

Bulk graphitic carbon nitride (CN) was synthetized by heating of melamine at 550 °C, and the exfoliated CN (ExCN) was prepared by heating of CN at 500 °C. Sulfur-doped CN was synthesized by heating of thiourea (S-CN) and by a novel procedure based on the post-synthetic derivatization of CN with methanesulfonyl (CH3SO2−) chloride (Mes-CN and Mes-ExCN). The obtained nanomaterials were investigated by common characterization methods and their photocatalytic activity was tested by means of the decomposition of acetic orange 7 (AO7) under ultraviolet A (UVA) irradiation. The content of sulfur in the modified CN decreased in the sequence of Mes-ExCN > Mes-CN > S-CN. The absorption of light decreased in the opposite manner, but no influence on the band gap energies was observed. The methanesulfonyl (mesyl) groups connected to primary and secondary amine groups were confirmed by high resolution mass spectrometry (HRMS). The photocatalytic activity decreased in the sequence of Mes-ExCN > ExCN > CN ≈ Mes-CN > S-CN. The highest activity of Mes-ExCN and ExCN was explained by the highest amounts of adsorbed Acetic Orange 7 (AO7). In addition, in the case of Mes-ExCN, chloride ions incorporated in the CN lattice enhanced the photocatalytic activity as well.

No abstract

No abstract

Graphitic carbon nitride (CN) was synthesized from guanidine hydrochloride (G), melamine (M) and dicyandiamide (DCDA). The CN materials synthetized from the pure precursors and their mixtures were characterized by common methods, including thermal analysis, and their photocatalytic activities were tested by the degradation of selected organic pollutants, such as amoxicillin, phenol, Rhodamine B (RhB). Remarkable changes in their texture properties in terms of particle sizes, specific surface areas (SSA) and consequently their photocatalytic activity were explained by the role of guanidine hydrochloride in their synthesis. The SSA increased due to the release of NH3 and HCl and its complex reactions with melamine and DCDA forming structure imperfections and disruptions. The photocatalytic activity of the CN materials was found to be dependent on their SSA.

No abstract