The contact of nanoparticles with biological fluids such as serum results in rapid adsorption of proteins at the nanoparticle surface in a layer known as the "protein corona". Protein coatings modify and control the behavior of the nanoparticles potentially altering the aggregation state and cellular response, which may influence their fate and hazard to human health. Cells are likely to interact with the protein interface rather than with bare surface; therefore it is important to study the protein layer and develop appropriate measurement tools. In this study we investigate how adsorbed proteins from serum affect the size and the surface charge of plain and aminated silica nanoparticles. Particle size and size distributions in buffer and serum-based biological media were studied using tunable resistive pulse sensing (TRPS), as well as differential centrifugal sedimentation (DCS) and dynamic light scattering (DLS). Average and single particle ζ-potentials (related to surface charge) were also measured by electrophoretic light scattering (ELS) and TRPS, respectively. Size measurements showed an increase in size of the nanoparticles upon acquisition of a protein layer, thus allowing an estimation of its thickness. DLS proved incapable of providing an accurate measurement of the nanoparticles' size in serum due to the presence of agglomerates. The ability of TRPS to measure sample agglomeration was investigated by comparison with the high resolution technique of DCS. Particle-by-particle ζ-potential measurements by TRPS were consistent with those performed with ELS and allowed a description of the ζ-potential distribution within the samples.

Four common size analysis techniques were applied to engineered silica nanoparticles suspended in purified water, in physiological buffer and in cell culture medium, and the results were compared using uncertainty estimates.

The surface charge density of nanoparticles plays an important role in the way they interact with biological systems. The ability to measure the surface charge density of nanoparticles in biological media is therefore of importance in understanding the magnitude of such interactions. There are a number of methods which may be used to assess surface charge density through the measurement of electrophoretic mobility. In order to better understand the comparability of these methods, the z-potential of silica nanoparticles in water, buffer and serum-based biological medium was measured by one ensemble and two particle-byparticle techniques: electrophoretic light scattering (ELS), tunable resistive pulse sensing (TRPS) and zeta particle tracking analysis (z-PTA). To allow the comparability of results from different techniques, test samples were prepared according to an established protocol, although some variations were necessary to meet specific instrument requirements. Here we compare, for the first time, measurement results from the different techniques and discuss how modifications related to parameters such as environmental pH, dilution factor and presence of biomolecules influence the charge measurements.

Analytical centrifugation in sedimentation and flotation modes is used to measure both the size and density of polystyrene nanoparticles.

When nanoparticles are introduced into biological media, they acquire a protein corona. The thickness of immunoglobulin G protein on 105 nm polystyrene particles has been determined by dynamic light scattering (DLS), differential centrifugal sedimentation (DCS) and small‐angle X‐ray scattering (SAXS). All three techniques measured an increase of the protein shell thickness with increasing concentration of the proteins during incubation with the nanoparticles. DLS measurements showed the highest increase, indicating a possible effect of particle agglomeration on the DLS results. DCS accuracy critically depends on the knowledge of the protein shell density but the data allows an estimation of the effective shell density when the thickness was independently determined. SAXS measurements revealed the complex core/shell structure of the bare polystyrene particles. © 2014 Crown Copyright. Surface and Interface Analysis © 2014 John Wiley & Sons Ltd.

This paper describes the production and characteristics of the nanoparticle test materials prepared for common use in the collaborative research project NanoChOp (Chemical and optical characterization of nanomaterials in biological systems), in casu suspensions of silica nanoparticles and CdSe/CdS/ZnS quantum dots (QDs). This paper is the first to illustrate how to assess whether nanoparticle test materials meet the requirements of a “reference material” (ISO Guide 30, 2015) or rather those of the recently defined category of “representative test material (RTM)” (ISO/TS 16195, 2013). The NanoChOp test materials were investigated with small-angle X-ray scattering (SAXS), dynamic light scattering (DLS), and centrifugal liquid sedimentation (CLS) to establish whether they complied with the required monomodal particle size distribution. The presence of impurities, aggregates, agglomerates, and viable microorganisms in the suspensions was investigated with DLS, CLS, optical and electron microscopy and via plating on nutrient agar. Suitability of surface functionalization was investigated with attenuated total reflection Fourier transform infrared spectrometry (ATR-FTIR) and via the capacity of the nanoparticles to be fluorescently labeled or to bind antibodies. Between-unit homogeneity and stability were investigated in terms of particle size and zeta potential. This paper shows that only based on the outcome of a detailed characterization process one can raise the status of a test material to RTM or reference material, and how this status depends on its intended use.

The influence of fluorescence on nanoparticle size measurements using dynamic light scattering (DLS) and small angle X-ray scattering (SAXS) was investigated.

The factors that affect the accuracy and precision of differential centrifugal sedimentation (DCS) for the analysis of nanoparticle concentration are described.