Wood sawdust is a solid residue, generated in the timber industry, which is of no profitable use and can cause serious environmental problems if disposed inadequately. The aim of this study was to use the eucalyptus sawdust in the preparation of activated carbons AC) and test them as adsorbents of methylene blue (MB) and phenol, representative pollutants from aqueous effluents of various industries. The eucalyptus sawdust was characterized by instrumental analysis such as elementary analysis (CHNS-O), thermogravimetric analysis (TGA), infrared spectroscopy (FTIR) and scanning electron microscopy (SEM , respectively, for MB and phenol).Index terms: Agro-industrial residues, adsorbents, pollutants. RESUMOA serragem é um resíduo sólido, gerado na indústria madeireira, que não tem uso rentável e pode causar sérios problemas ambientais quando disposta inadequadamente. Neste estudo, objetivou-se utilizar a serragem de eucalipto na preparação de carvões ativados (AC) e testá-los como adsorventes do corante azul de metileno (MB) e fenol; moléculas que representam poluentes de efluentes industriais. A serragem de eucalipto foi caracterizada por análises instrumentais, tais como: análise elementar (CHNS-O), análise termogravimétrica (TGA), espectroscopia na região do infravermelho (FTIR) e microscopia eletrônica de varredura (SEM). Os carvões ativados foram preparados por ativação física com dióxido de carbono AC_CO 2 , (10º Cmin , respectivamente, para MB e fenol). Termos para indexação:Resíduos agroindustriais, adsorventes, poluentes.
ABSTRACT:The use of biomass for biochar production is already a reality. However, little is known about its structure and composition, mainly due to the changes occurred during the heat treatment. This information is crucial since it will have an immediate impact on the quality and applicability of the material produced. Therefore, this study aimed to analyze different biomasses, characterizing their potential for biochar production. Woods from Eucalyptus urophylla and Corymbia citriodora and coffee husk were assessed. The biomass was ground and sieved, and then stored under controlled conditions of temperature and humidity. Subsequently, the material characterizations were performed through proximate analysis, elemental analysis, thermogravimetric analysis and Fourier transform infrared spectroscopy (FTIR). In general, all biomasses presented potential to be used in the production of biochar, where low H/C and O/C ratios were found. The coffee husk has higher lignin, extractives, ash and fixed carbon contents, which certainly contributed to its greater thermal stability. The FTIR analysis showed the presence of bands related to recalcitrant chemical groups such as carboxylics and phenolics in the spectra of all biomasses. The thermogram profiles of the C. citriodora and E. urophylla wood were similar to each other, and different from that of the coffee husk, which showed higher thermal stability. CARACTERIZAÇÃO DE DIFERENTES BIOMASSAS VEGETAIS PARA PRODUÇÃO DE BIOCARVÕESRESUMO: A utilização da biomassa para produção de biocarvões já é uma realidade. Porém, pouco se sabe sobre a sua estrutura e composição, principalmente, mediante as transformações ocorridas durante o tratamento térmico. Estas informações são fundamentais, uma vez que terão impacto imediato na qualidade e aplicabilidade do material produzido. Portanto este trabalho objetivou analisar diferentes biomassas, caracterizando-as como potenciais para produção de biocarvões. Foram utilizadas madeiras de Eucalyptus urophylla e Corymbia citriodora e cascas de café. As biomassas foram moídas e peneiradas e, em seguida, armazenadas sob condições de temperatura e umidade controlada. Posteriormente realizou-se a caracterização dos materiais, por meio de análise química, química imediata, elementar (CHNS-O), térmica (TGA e DTA) e de espectroscopia vibracional na região do infravermelho (FTIR). De forma geral, todas as biomassas apresentaram potencial para serem utilizadas na produção de biocarvão, no entanto, a casca de café apresentou maiores teores de lignina, extrativos, cinzas e carbono fixo, o que, certamente, contribuiu para que a mesma apresentasse maior potencial de utilização como condicionador de solos. Com relação à análise de FTIR, observou-se a presença de bandas referentes aos grupos químicos recalcitrantes, como os carboxílicos e fenólicos nos espectros de todas as biomassas. O perfil dos termogramas de C. citriodora e de E. urophylla foram semelhantes entre si e diferentes da casca de café, que apresentou maior estabilidade térmica.
ResumoEste trabalho teve como objetivo caracterizar mecanicamente amostras individuais da madeira e do carvão vegetal de Corymbia citriodora e de clones de Eucalyptus urophylla, por meio de ensaios de compressão paralela às fibras e de flexão estática, e ainda, correlacionar as propriedades da madeira com as do carvão produzido. Foram utilizadas 148 amostras, sendo que 74 foram destinadas à avaliação do carvão e 74 à avaliação da madeira. As amostras destinadas ao processo de carbonização foram submetidas a uma taxa de aquecimento de 0,5ºC/min e temperatura final de 450ºC. A madeira e o carvão de C. citriodora apresentaram valores superiores de densidade, rigidez, resistência à compressão e módulo de ruptura, quando comparados à madeira e ao carvão de E. urophylla, indicando ser mais adequados ao uso siderúrgico. O carvão vegetal apresentou forte correlação apenas com a densidade básica da madeira, sendo de média a baixa correlação com o restante das propriedades, mostrando que apenas a densidade básica da madeira pode ser utilizada para prever o comportamento mecânico do carvão vegetal. Palavras-chave: Eucalyptus, carbonização, rigidez e resistência. AbstractThis study aimed to characterize mechanically the wood and charcoal of individual pieces of Corymbia citriodora and Eucalyptus urophylla clones through parallel compression tests for fibers and static flexion, and to correlate the properties of the wood with that of the coal produced. 148 specimens were used, of which 74 were used for the evaluation of the charcoal and 74 for the evaluation of the wood. The test specimens for charcoal evaluation were carbonized at a heating rate of 0.5 °C/min and final temperature of 450 ° C. The wood and charcoal of C. citriodora showed significantly higher values of density, stiffness, compressive strength and modulus of rupture when compared to the wood and the charcoal of E. urophylla, indicating to be more suitable for the steel industry. The charcoal showed a strong correlation only with the basic density of the wood, having on average a low correlation with the rest of the properties, indicating that only the basic density of the wood can be used to predict the mechanical behavior of charcoal.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
334 Leonard St
Brooklyn, NY 11211
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.