Research of the possibility of using an electrical discharge machining metal powder in selective laser melting Abstract. In this paper the research of a Ni-20Cr-10Fe-3Ti (heat-resistant) alloy metal powder conducted for use in a selective laser melting technology. This metal powder is the slime after electric discharge machining. The technology of cleaning and melting the powder discussed in this article. As a control input of the powder, immediately before 3D printing, dimensional analysis, surface morphology and the internal structure of the powder particles after the treatment were examined using optical and electron microscopes. The powder granules are round, oval, of different diameters with non-metallic inclusions. The internal structure of the particles is solid with no apparent defects. The content of the required diameter of the total volume of test powder granules was 15%. X-ray fluorescence analysis of the powder materials carried out. The possibility of powder melting was investigated in the selective laser melting machine 'SLM 280HL'. A selection of the melting modes based on the physical properties of the Ni-20Cr-10Fe-3Ti alloy, data obtained from similar studies and a mathematical model of the process. Conclusions on the further investigation of the possibility of using electric discharge machining slime were made.
Методами просвечивающей электронной дифракционной микроскопии тонких фольг выполнено исследование элементного состава и состояния дефектной субструктуры покрытия, полученного методом селективного лазерного сплавления порошка высокопрочного жаропрочного никелевого сплава ВВ751П (ХН56КВМТЮБ) на подложке из титанового сплава ВТ20. Покрытие было создано путем нанесения двух слоев порошка с помощью СЛС на установке SLM 280HL (среда инертного газа азот, мощность лазерного излучения 295 Вт, скорость сканирования 710 мм/с, угол штриховки 45 град). Исследование выявило формирование поликристаллической структуры. Морфология структуры спеченного слоя порошка практически не зависит от расстояния от поверхности спекания и характеризуется наличием кристаллитов, размеры которых изменяются от десятков нанометров до единиц микрометров. Методами микрорентгеноспектрального анализа выполнено исследования элементного состава. Установлено, что толщина спекаемого слоя порошка не превышает (100120) мкм. Спеченный слой обогащен титаном и является неоднородным. На расстоянии (5060) мкм от поверхности спекания выявляется максимум концентрации атомов Ni, Co, Cr, Nb. Анализ мест локализации химических элементов в покрытии выполнен методом картирования тонких фольг. Установлено неоднородное распределение атомов титана. Размеры кристаллитов, обогащенных титаном, изменяются в пределах от 100 нм до 500 нм. На глубине, превышающей 70 мкм атомы титана распределены в объеме спеченного слоя квазиравномерно. Выявлено неоднородное распределение атомов хрома, которые формируют протяженные прослойки вдоль границ субзеренной структуры. Области, обогащенные атомами никеля, располагаются в объеме зерен твердого раствора на основе титана и имеют размеры, изменяющиеся в пределах от 120 нм до 300 нм.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.