If perovskite solar cells (PSCs) with high power conversion efficiencies (PCEs) are to be commercialized, they must achieve long-term stability, which is usually assessed with accelerated degradation tests. One of the persistent obstacles for PSCs has been successfully passing the damp-heat test (85°C and 85% relative humidity), which is the standard for verifying the stability of commercial photovoltaic (PV) modules. We fabricated damp heat–stable PSCs by tailoring the dimensional fragments of two-dimensional perovskite layers formed at room temperature with oleylammonium iodide molecules; these layers passivate the perovskite surface at the electron-selective contact. The resulting inverted PSCs deliver a 24.3% PCE and retain >95% of their initial value after >1000 hours at damp-heat test conditions, thereby meeting one of the critical industrial stability standards for PV modules.

We report on bulk-heterojunction (BHJ) organic photovoltaics (OPVs) based on the self-assembled monolayer (SAM) 2PACz as a hole-selective interlayer functionalized directly onto the indium tin oxide (ITO) anode. The 2PACz is found to change the work function of ITO while simultaneously affecting the morphology of the BHJ deposited atop. Cells with PM6:N3 BHJ and ITO-2PACz anode exhibit a power conversion efficiency (PCE) of 16.6%, which is greater than that measured for bare ITO (6.45%) and ITO/PEDOT:PSS (15.94%) based devices. The enhanced performance is attributed to lower contact-resistance, reduced bimolecular recombination losses, and improved charge transport within the BHJ. Importantly, the ITO-2PACz-based OPVs show dramatically improved operational stability when compared with PEDOT:PSS-based cells. When the ITO-2PACz anode is combined with the ternary PM6:BTP-eC9:PC 71 BM BHJ, the resulting cells exhibit a maximum PCE of 18.03%, highlighting the potential of engineered SAMs for use in hole-selective contacts in high-performance OPVs.

Hybrid organic-inorganic semiconducting perovskite photovoltaic cells are usually coupled with organic hole conductors. Here, we report planar, inverse CH3NH3PbI3-xClx-based cells with inorganic hole conductors. Using electrodeposited NiO as hole conductor, we have achieved a power conversion efficiency of 7.3%. The maximum VOC obtained was 935 mV with an average VOC value being 785 mV. Preliminary results for similar cells using electrodeposited CuSCN as hole conductor resulted in devices up to 3.8% in efficiency. The ability to obtain promising cells using NiO and CuSCN expands the presently rather limited range of available hole conductors for perovskite cells.

The performance of perovskite solar cells with inverted polarity ( p-i-n ) is still limited by recombination at their electron extraction interface, which also lowers the power conversion efficiency (PCE) of p-i-n perovskite-silicon tandem solar cells. A ~1 nm thick MgF x interlayer at the perovskite/C 60 interface through thermal evaporation favorably adjusts the surface energy of the perovskite layer, facilitating efficient electron extraction, and displaces C 60 from the perovskite surface to mitigate nonradiative recombination. These effects enable a champion V oc of 1.92 volts, an improved fill factor of 80.7%, and an independently certified stabilized PCE of 29.3% for a ~1 cm 2 monolithic perovskite-silicon tandem solar cell. The tandem retained ~95% of its initial performance following damp-heat testing (85 Celsius at 85% relative humidity) for > 1000 hours.

Bifacial monolithic perovskite/silicon tandem solar cells exploit albedo-the diffuse reflected light from the environment-to increase their performance above that of monofacial perovskite/silicon tandems. Here we report bifacial tandems with certified power conversion efficiencies >25% under monofacial AM1.5G 1 sun illumination that reach power-generation densities as high as ~26 mW cm -2 under outdoor testing. We investigated the perovskite bandgap required to attain optimized current matching under a variety of realistic illumination and albedo conditions. We then compared the properties of these bifacial tandems exposed to different albedos and provide energy yield calculations for two locations with different environmental conditions. Finally, we present a comparison of outdoor test fields of monofacial and bifacial perovskite/silicon tandems to demonstrate the added value of tandem bifaciality for locations with albedos of practical relevance.