Stacking solar cells with decreasing band gaps to form tandems presents the possibility of overcoming the single-junction Shockley-Queisser limit in photovoltaics. The rapid development of solution-processed perovskites has brought perovskite single-junction efficiencies >20%. However, this process has yet to enable monolithic integration with industry-relevant textured crystalline silicon solar cells. We report tandems that combine solution-processed micrometer-thick perovskite top cells with fully textured silicon heterojunction bottom cells. To overcome the charge-collection challenges in micrometer-thick perovskites, we enhanced threefold the depletion width at the bases of silicon pyramids. Moreover, by anchoring a self-limiting passivant (1-butanethiol) on the perovskite surfaces, we enhanced the diffusion length and further suppressed phase segregation. These combined enhancements enabled an independently certified power conversion efficiency of 25.7% for perovskite-silicon tandem solar cells. These devices exhibited negligible performance loss after a 400-hour thermal stability test at 85°C and also after 400 hours under maximum power point tracking at 40°C.

Bifacial monolithic perovskite/silicon tandem solar cells exploit albedo-the diffuse reflected light from the environment-to increase their performance above that of monofacial perovskite/silicon tandems. Here we report bifacial tandems with certified power conversion efficiencies >25% under monofacial AM1.5G 1 sun illumination that reach power-generation densities as high as ~26 mW cm -2 under outdoor testing. We investigated the perovskite bandgap required to attain optimized current matching under a variety of realistic illumination and albedo conditions. We then compared the properties of these bifacial tandems exposed to different albedos and provide energy yield calculations for two locations with different environmental conditions. Finally, we present a comparison of outdoor test fields of monofacial and bifacial perovskite/silicon tandems to demonstrate the added value of tandem bifaciality for locations with albedos of practical relevance.

Sputtered nickel oxide (NiOx) is an attractive hole‐transport layer for efficient, stable, and large‐area p‐i‐n metal‐halide perovskite solar cells (PSCs). However, surface traps and undesirable chemical reactions at the NiOx/perovskite interface are limiting the performance of NiOx‐based PSCs. To address these issues simultaneously, an efficient NiOx/perovskite interface passivation strategy by using an organometallic dye molecule (N719) is reported. This molecule concurrently passivates NiOx and perovskite surface traps, and facilitates charge transport. Consequently, the power conversion efficiency (PCE) of single‐junction p‐i‐n PSCs increases from 17.3% to 20.4% (the highest reported value for sputtered‐NiOx based PSCs). Notably, the N719 molecule self‐anchors and conformally covers NiOx films deposited on complex surfaces. This enables highly efficient textured monolithic p‐i‐n perovskite/silicon tandem solar cells, reaching PCEs up to 26.2% (23.5% without dye passivation) with a high processing yield. The N719 layer also forms a barrier that prevents undesirable chemical reactions at the NiOx/perovskite interface, significantly improving device stability. These findings provide critical insights for improved passivation of the NiOx/perovskite interface, and the fabrication of highly efficient, robust, and large‐area perovskite‐based optoelectronic devices.

Perovskite light-emitting diodes (LEDs) have attracted broad attention due to their rapidly increasing external quantum efficiencies (EQEs) [1][2][3][4][5][6][7][8][9][10][11][12][13][14][15] . However, most high EQEs of perovskite LEDs are reported at low current densities (< 1 mA cm -2 ) and low brightness. Decrease in efficiency and rapid degradation at high brightness inhibit their practical applications. Here,

Perovskite/silicon tandem solar cells are emerging as a highefficiency and prospectively cost-effective solar technology with great promise for deployment at the utility scale. However, despite the remarkable performance progress reported lately, assuring sufficient device stabilityparticularly of the perovskite top cellremains a challenge on the path to practical impact. In this work, we analyze the outdoor performance of encapsulated bifacial perovskite/silicon tandems, by carrying out field-testing in Saudi Arabia. Over a six month experiment, we find that the open circuit voltage retains its initial value, whereas the fill factor degrades, which is found to have two causes. A first degradation mechanism is linked with ion migration in the perovskite and is largely reversible overnight, though it does induce hysteretic behavior over time. A second, irreversible, mechanism is caused by corrosion of the silver metal top contact with the formation of silver iodide. These findings provide directions for the design of new and more stable perovskite/silicon tandems

No abstract

Textured silicon wafers used in silicon solar cell manufacturing offer superior light trapping, which is a critical enabler for high-performance photovoltaics. A similar optical benefit can be obtained in monolithic perovskite/silicon tandem solar cells, enhancing the current output of the silicon bottom cell. Yet, such complex silicon surfaces may affect the structural and optoelectronic properties of the overlying perovskite films. Here, through extensive characterization based on optical and microstructural spectroscopy, it is found that the main effect of such substrate morphology lies in an altering of the photoluminescence response of the perovskite, which is associated with thickness variations of the perovskite, rather than lattice strain or compositional changes. With this understanding, the design of high-performance perovskite/silicon tandems is rationalized, yielding certified power conversion efficiencies of >28%.

Long‐chain organic halide salts are widely used in perovskite‐based optoelectronic devices for surface passivation owing to their capability to interact with the surface defects of perovskites. Here, aluminum oxide (AlOx) is introduced via atomic layer deposition onto octylammonium iodide (OAI) to exploit the benefits of organic halide salts without generating undesired defects. The devices incorporating AlOx on OAI‐treated perovskite (OAI/AlOx) show enhancement in both device performance and photo‐stability compared to those with only treatment. A diffusion of aluminum from AlOx into the perovskite through surface characterization contributes to a uniform photo‐generated carrier transport in both the surface and the bulk of the perovskite absorber. In addition, it is revealed that light‐induced two‐dimensional perovskite formation on OAI/AlOx. This may be ascribed to preventing the loss of OA cations due to the presence of AlOx, leading to a decrease in the number of iodine anions which suppresses the light‐induced degradation of corresponding devices. Consequently, the devices show over 24% efficiency and retain their efficiency over 1000 hours under continuous light illumination.