Orifice is a device that is placed in a pipe flow to inhibit the flow of fluid and cause a pressure drop. The measurement of the flow rate (flow rate) is obtained from the difference in pressure due to the pressure drop. In this study, it analyzed the influence of differences in plate orifice thickness variations used ranging from 2 mm to 4 mm thick with variations in increments every 0.5 mm with an orifice center hole diameter of 1.5 cm. Orifice placement is placed in an area whose speed profile is still changing or called the entrance region with a pipe diameter used 2.54 cm (1 Inch) diameter in the pipe. Then along the entrance area are paired 12 piezometer points along 75 cm with a position of laying 6 piezometer points before the orifice valve and 6 piezometer points after the orifice valve and in this experiment set the Re value to 3 Variations of Re, namely Re 1: 9784.5; Re2: 14647.5; Re 3: 19510.45 and this experiment was carried out at a temperature of 27 °C. In this study, the results were obtained for the highest irrecoverable pressure drop value located in the flow discharge with Re 19510.45 and at the thickness of the plate orifice 4 mm with an irrecoverable pressure drop value of 3033.01 Pa and while for the lowest irrecoverable pressure drop value, it was located in the flow discharge with a value of Re 9784.5 at an orifice plate thickness of 2 mm with an irrecoverable pressure drop value of 548.26 Pa. The highest discharge of coefficient (Cd) value lies in the flow discharge with a value of Re 14647.5 at the plate orifice thickness of 3.5 with a Cd value of 0.718 and while for the lowest discharge of coefficient (Cd) value lies in the flow discharge with Re 14647.5 with an orifice plate thickness of 2 mm with a Cd value of 0.609.
Ketika seseorang mengalami kecacatan pada bagian kaki yang dapat menghalangi aktifitas, maka di perlukan alat bantu yaitu kursi roda. Kursi roda yang umumnya digunakan adalah kursi roda yang bekerja secara manual. Pada Mindy Wheelchair yakni kursi roda yang dikontrol dengan sinyal otak (EEG), kursi roda manual akan dimodifikasi terlebih dahulu agar dapat bekerja secara elektrik. Desain kursi roda elektrik harus dapat bergerak pada jalan yang datar sesuai dengan perintah yang diberikan melalui sinyal otak. Ada 5 arah pergerakan kursi roda yang akan dikontrol yakni Maju, Mundur, Kiri, Kanan dan Stop. Pada Kursi roda juga ditambahkan 2 buah sensor ultasonik sebagai pengaman untuk mengetahui adanya halangan pada bagian depan dan kursi roda. Pada saat kursi roda bergerak maju, maka sensor ultrasonic belakang akan mati dan ketika pergerakan mundur, maka sensor ultrasonic depan tidak aktif. Dari hasil yang didapatkan bahwa kursi roda berhasil dibuat dengan batas maksimal beban sebesar 118 Kg dengan kcepatan yang diatur pada ± 0,72 Km/Jam.
Saat ini perkembangan teknologi berkembang dengan sangat cepat dan pesat. Salah satu contohnya adalah otomatisasi sistem keamanan rumah.Salah satu yang saat ini sedang berkembang adalah proses otomatisasi di dalam rumah yaitu Miniatur Smart Home Berbasis SMS dan Arduino.Sistem ini berfungsi sebagai sistem untuk menghidupkan dan mematikan lampu berbasis Short Message Service (SMS) dan juga menggunakan beberapa sensor untuk keamanan rumah dengan mengoptimalkan board Arduino sebagai pengontrol dan pengumpul data. GSM shield 900 sebagai penghubung informasi ke handphone dan Arduino sebagai pusat pengendali dan pengolahan data yang nantinya akan memberikan perintah kepada relay untuk menyalakan dan mematikan lampu. Sistem ini terdiri dari tiga buah sensor yaitu sensor gerakan (PIR) untuk mendeteksi adanya motion atau pergerakan dalam setiap ruangan, sensor MQ-02 untuk mendeteksi adanya gas kemudian pesan akan dikirim ke seluler dan sekaligus akan menghidupkan kipas maupun buzzer, dan flame sensor untuk mendeteksi adanya api kemudian pesan akan dikirim ke seluler dan sekaligus akan mematikan api kompor.Dalam sistem ini juga ada sistem miniatur buka tutup pagar. Kata kunci : Arduino Uno, GSM shield 900, PIR, Buzzer, Relay
Currently steel pipes are needed, especially in construction work. Construction with pipe materials cannot be separated from the process of joining and cutting. The cutting process for large pipes always uses a thermal cutting process. This study aims to determine how much influence the cutting distance has on the cutting results on a pipe that rotates at a constant 0.8 rpm following the shape of the corner joint contour. To achieve the objectives of this study, a pipe cutting tool with a diameter of 4 to 6 inches is needed with the thermal cutting method using the Oxy Acetylene Cutting (OAC) process This research data was obtained by cutting the 4inch pipe schedule 10s, schedule 20s and schedule 40s in a rotating condition and the cutting torch moves back and forth. The pipe rotates at 0.8 rpm using an AC motor transmitted using a gearbox connected to the wheel as a holder where the pipe rotates. The results of the cutting are in the form of a pipe connection contour with an angle of 900 and 600. As the independent variable in this study was set the cutting distance is 5mm, 7mm and 10 mm, while the fixed variables are determined by cutting speed 280 mm/minute, acetylene gas pressure 3.5 kg/cm2 and oxygen 17.5 kg/cm2. In order to get effective results, preheat the surface of the pipe with a gas fuel mixture until it reaches the melting temperature of the pipe as the main ingredient. The cutting results that meet the entire path of the pipe can be cut completely and through and there is very little splash or melt dirt during the cutting process. After cutting, the best results are obtained at a cutting distance of 5 mm both on schedule 10s, schedule 20s and schedule 40s.
Rancang bangun robot penyaji minuman ini berfungsi untuk menyajikan satu jenis ataupun campuran beberapa minuman. Minuman yang dapat disediakan adalah 8 jenis bahan minuman dan 8 jenis campuran bahan minuman tersebut. Cara kerja robot ini dimulai dari penekanan keypad sebagai input. Kemudian mikrokontroler ATMega 8535 mengaktifkan motor stepper 1 dan 2. Setelah gelas berada tepat di bawah wadah bahan minuman yang telah dipilih maka mikrokontroler mengaktifkan mini water pump untuk memompa minuman dari wadah ke gelas. Jika yang dipilih adalah minuman campuran maka setelah semua bahan minuman dimasukkan selanjutnya motor stepper akan aktif kembali dan membawa gelas menuju ke tempat pengadukan (mixer). Ketika gelas tepat berada dibawah mixer maka silinder aksi tunggal yang membawa mixer turun hingga beberapa saat kemudian mixer akan aktif. Keunggulan robot ini adalah dapat bergerak ke bahan minuman dengan pergerakan x dan y serta dapat mengaduk minuman. Dari pengujian yang sudah dilakukan robot ini dapat mengenali pesanan minuman yang sudah dibuat pengguna sebelumnya dan mampu menyajikan minuman tersebut dengan benar dengan unjuk kerja keberhasilan sebesar 100%. Rata-rata lamanya waktu yang dibutuhkan untuk menyajikan minuman yang hanya terdiri atas 1 jenis bahan saja adalah sebesar 33,28 detik dan untuk jenis minuman campuran 2 atau 3 bahan membutuhkan waktu rata-rata selama 37,9 detik. Robot juga mampu melakukan proses pengadukan untuk jenis minuman campuran dengan baik dengan unjuk kerja keberhasilan sebesar 100%.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.