A distributed optical fibre sensor is introduced which is capable of quantifying multiple dynamic strain perturbations along 1 km of a sensing fibre simultaneously using a standard telecommunication single-mode optical fibre. The technique is based on measuring the phase between the Rayleigh scattered light from two sections of the fibre which define the gauge length. The phase is spatially determined along the entire length of the fibre with a single pulse. This allows multiple moving strain perturbation to be tracked and quantified along the entire length of the fibre. The demonstrated setup has a spatial resolution of 2 m with a frequency range of 500-5000 Hz. The minimum detectable strain perturbation of the sensor was measured to be 80 n .

Extensive research on Brillouin- and Raman-based distributed optical fibre sensors over the past two decades has resulted in the commercialization of distributed sensors capable of measuring static and quasi-static phenomena such as temperature and strain. Recently, the focus has been shifted towards developing distributed sensors for measurement of dynamic phenomena such as dynamic strain and sound waves. This article reviews the current state of the art distributed optical fibre sensors capable of quantifying dynamic vibrations. The most important aspect of Rayleigh and Brillouin scattering processes which have been used for distributed dynamic measurement are studied. The principle of the sensing techniques used to measure dynamic perturbations are analyzed followed by a case study of the most recent advances in this field. It is shown that the Rayleigh-based sensors have longer sensing range and higher frequency range, but their spatial resolution is limited to 1 m. On the other hand, the Brillouin-based sensors have shown a higher spatial resolution, but relatively lower frequency and sensing ranges.

A distributed optical fiber dynamic strain sensor with high spatial and frequency resolution is demonstrated. The sensor, which uses the ϕ-OTDR interrogation technique, exhibited a higher sensitivity thanks to an improved optical arrangement and a new signal processing procedure. The proposed sensing system is capable of fully quantifying multiple dynamic perturbations along a 5 km long sensing fiber with a frequency and spatial resolution of 5 Hz and 50 cm, respectively. The strain resolution of the sensor was measured to be 40 nε.

Trackside monitoring of railways provides useful data for understanding the condition and mechanical behaviour of railway track, prior research has shown that railway track performance varies significantly along its length, primarily owing to changing support conditions. Understanding the changing performance along track offers the potential for improved track design and maintenance. Different technologies are used to investigate this. For example, inertial sensors, or high-speed filming with digital image correlation (DIC) for track deflection, and traditional strain gauges for loads. The latter usually rely on in-situ calibration. These techniques are suitable for measurements at discrete locations along the track length but are not suited to measuring performance variability even along a few hundred meters of a railway line. This paper investigates the use of a recently developed sensing system known as distributed acoustic sensor (DAS) that uses optical fibres. This method has the potential to be used over very long lengths of track; offers high sample rates; and has a gauge length and spatial resolution suitable for investigating the load-deflection behaviour of the track. This study presents DAS optical fibre strain measurements from a study site and presents novel methods for determining the rail deflection and the load per sleeper end. The DAS results are compared with point location measurements using a traditional strain gauge and deflections determined using imaging and DIC. The DAS system offers reliable distributed strain measurement that convert to estimates of track deflection and load with the potential for continuous spatial and temporal coverage over significant lengths of track.

A distributed optical fibre acoustic sensor is numerically modelled. To increase the flexibility of the model, the building blocks of the sensing system are modelled separately and later combined to form the numerical model. This approach is adopted to facilitate the evaluation of each of the individual building blocks and their effects on the output of the sensor. The numerical model is used to assess the effect of parameters such as the linewidth of the laser source, the width of the probe pulse, and the frequency and amplitude of perturbation on the response of the sensing system. It is shown that the precision and accuracy of the sensing system are affected by the frequency and amplitude of perturbation as well as the pulse width and linewidth of the probe pulse.

A Brillouin-based distributed optical fiber dynamic strain sensor is described which converts strain-induced Brillouin frequency shift into optical intensity variations by using an imbalanced Mach-Zhender interferometer. A 3×3 coupler is used at the output of this interferometer to permit differentiate and cross multiply demodulation. The demonstrated sensor is capable of probing dynamic strain disturbances over 2 km of sensing length every 0.5 s up to a strain of 10 mε with an accuracy of ±50 με and spatial resolution of 1.3 m.

We present a low-noise distributed acoustic sensor using enhanced backscattering fiber with a series of localized reflectors. The point reflectors were inscribed in a standard telecom fiber in a fully automated system by focusing an ultra-fast laser through the fiber cladding. The inscribed reflectors provided a reflectance of −53 dB, significantly higher than the Rayleigh backscattering level of −70 dB/m, despite adding only 0.01 dB of loss per 100 reflection points. We constructed a coherent φ-OTDR system using a double-pulse architecture to probe the enhanced backscattering fiber. Using this system, we found that the point reflectors enabled an average phase noise of −91 dB (re rad2/Hz), 20 dB lower than sensors formed using Rayleigh backscattering in the same fiber. The sensors are immune to interference fading, exhibit a high degree of linearity, and demonstrate excellent non-local signal suppression (>50 dB). This work illustrates the potential for low-cost enhanced backscattering fiber to enable low-noise, long-range distributed acoustic sensing.

A novel subsea cable condition monitoring technique based on embedded optical fibre inside the cable is demonstrated. It is shown that a distributed optical fibre vibration sensor can be used to map dynamic strains all along the cable simultaneously. It is experimentally shown that such system can fully quantify the location and strain level at each point on the cable as a function of time for both abrupt impact and cyclical loading. The sensing system demonstrated a spatial and strain resolution of 1m and 4µε, respectively, over a 10km sensing range.