The objective of this ex vivo cadaver study was to determine the accuracy of cone beam computerized tomography (CBCT) and a 3-dimensional stereolithographic (STL) model in identifying and measuring the anterior loop length (ANLL) of the mental nerve. A total of 12 cadavers (24 mental nerve plexus) were used for this study. Standardized CBCT scans of each mandible were obtained both with and without radiographic contrast tracer injected into the mental nerve plexus, and STL models of the two acquired CBCT images were made. The ANLL were measured using CBCT, STL model, and anatomy. The measurements obtained from the CBCT images and STL models were then analyzed and compared with the direct anatomic measurements. A paired sample t test was used, and P values less than .05 were considered statistically significant. The mean difference between CBCT and anatomic measurement was 0.04 mm and was not statistically significant (P = .332), whereas the mean difference between STL models and anatomic measurement was 0.4 mm and was statistically significant (P = .042). There was also a statistical significant difference between CBCT and the STL model (P = .048) with the mean difference of 0.35 mm. Therefore, CBCT is an accurate and reliable method in determining and measuring the ANLL but the STL model over- or underestimated the ANLL by as much as 1.51 mm and 1.83 mm, respectively.
The objective of this ex vivo cadaver study was to determine the accuracy of cone beam computed tomography(CBCT) and 3D stereolithographic(STL) model in identifying and measuring the anterior loop length(ANLL) of the mental nerve. A total of 12 cadavers (24 mental nerve plexus) were used for this study. Standardized CBCT scans of each mandible were obtained both with and without radiographic contrast tracer injected into the mental nerve plexus. STL models of the two acquired CBCT images were made. ANLL were measured using CBCT, STL and anatomy. The measurements obtained from the CBCT images and STL models were then analyzed and compared with the direct anatomic measurements. Paired sample t-test was used. P values less than .05 was considered statistically significant. The mean difference between CBCT and anatomic measurement was 0.04mm and not statistically significant (p= .332) while the mean difference between STL and anatomic measurement was 0.4mm and statistically significant (p=.042). There was also a statistical significant difference between CBCT and STL (p=.048) with the mean difference of 0.35mm. Therefore, CBCT is an accurate and reliable method in determining and measuring the ANLL while the STL over or underestimated the ANLL by as much as 1.51mm and 1.83mm respectively.
The successful results of endosseous root form implants in the treatment of partially and completely edentulous patients has been made possible by the application of standardized surgical and prosthetic protocols. Different techniques have been published in the literature with the purpose of reducing implant prosthetic rehabilitation times. This clinical case report describes a new surgical concept and a technique to fabricate screw-retained provisional crowns for immediate loading of free-standing single tooth implants. Further clinical and histologic studies are necessary in order to promote routine clinical application of this technique.
Primary and secondary reconstruction of mandibular discontinuity defects with vascularized flap is currently the standard of care in many institutions. The most commonly used donor site for such flaps is fibula. Fibula provides enough bone length, allows 2-team approach, and has low donor site morbidity and abundant periosteal blood supply. The placement of endosseous implants in the vascularized fibula flap also facilitates functional dental rehabilitation. This clinical report describes the prosthetic rehabilitation and the complications of 2 mandibular discontinuity defects treated with vascularized fibula flap and implant-supported fixed prosthesis.
This article describes a technique in which an acellular dermal allograft is used in combination with a photopolymerized acrylic resin stent to increase the zone of keratinized tissue around osseointegrated dental implants. During the second-stage surgery, a split thickness labial flap is reflected and apically repositioned by being sutured onto the periosteum and connective tissue. The acellular dermal allograft is then sutured onto the recipient site. The acrylic resin is trimmed and secured with temporary abutments to the implants, fitting passively over the graft and then photopolymerized intraorally. The stent is left for 1 week to secure the graft in place. This technique offers an alternative mucogingival procedure for increasing the zone of keratinized tissue around osseointegrated dental implants.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.