This paper presents a life cycle assessment (LCA) study that examines a number of scenarios that complement the primary use phase of electric vehicle (EV) batteries with a secondary application in smart buildings in Spain, as a means of extending their useful life under less demanding conditions, when they no longer meet the requirements for automotive purposes. Specifically, it considers a lithium iron phosphate (LFP) battery to analyze four second life application scenarios by combining the following cases: (i) either reuse of the EV battery or manufacturing of a new battery as energy storage unit in the building; and (ii) either use of the Spanish electricity mix or energy supply by solar photovoltaic (PV) panels. Based on the Eco-indicator 99 and IPCC 2007 GWP 20a methods, the evaluation of the scenario results shows that there is significant environmental benefit from reusing the existing EV battery in the secondary application instead of manufacturing a new battery to be used for the same purpose and time frame. Moreover, the findings of this work exemplify the dependence of the results on the energy source in the smart building application, and thus highlight the importance of PVs on the reduction of the environmental impact.
Research on T-configuration aluminum constructions effectively decreases fuel consumption, increases strength, and develops aerial structures. In this research, the effects of friction stir welding (FSW) tool offset (TO) on Al–Mg–Si alloy mixing and bonding in T-configurations is studied. The process is simulated by the computational fluid dynamic (CFD) technique to better understand the material mixing flow and the bonding between the skin and flange during FSW. According to the results, the best material flow can be only achieved at an appropriate TO. The appropriate TO generates enough material to fill the joint line and results in formation of the highest participation of the flange in the stir zone (SZ) area. The results show that, in the T-configuration, FSW joints provide raw materials from the retreating side (RS) of the flange that play a primary role in producing a sound mixing flow. The selected parameters were related to the geometric limitations of the raw sheets considered in this study. The failure point of all tensile samples was located on the flange. Surface tunneling is the primary defect in these joints, which is produced at high TOs. Among the analyzed cases, the most robust joint was made at +0.2 mm TO on the advancing side (AS), resulting in more than 60% strength of the base aluminum alloy being retained.
This paper studies the influence of diverse friction models on the numerical analysis of an industrial skew rolling mill using FORGE®. The originality of the present contribution is the analysis of the effect of the friction model on important parameters, namely, consumed power, plastic deformation and surface temperature. The aim is to evaluate which of these friction models is appropriate for simulating these industrial processes. The high values of temperature, pressure and sliding velocity at the contacts make the assessment of the friction model incidence on the deformation and temperature evolution fundamental, given its importance on the thermomechanical processing of materials. As a conclusion, IFUM is not valid because of its sliding velocity approach. On the other hand, Neumaier presents the highest deviations in terms of experimental power. It is concluded that Tresca is valid for this sort of processes and Norton model gives the most accurate results for friction power, related to the high sliding conditions at the contact.
The evolution of the microstructure changes during hot deformation of high-chromium content of stainless steels (martensitic stainless steels) is reviewed. The microstructural changes taking place under high-temperature conditions and the associated mechanical behaviors are presented. During the continuous dynamic recrystallization (cDRX), the new grains nucleate and growth in materials with high stacking fault energies (SFE). On the other hand, new ultrafine grains could be produced in stainless steel material irrespective of the SFE employing high deformation and temperatures. The gradual transformation results from the dislocation of sub-boundaries created at low strains into ultrafine grains with high angle boundaries at large strains. There is limited information about flow stress and monitoring microstructure changes during the hot forming of martensitic stainless steels. For this reason, continuous dynamic recrystallization (cDRX) is still not entirely understood for these types of metals. Recent studies of the deformation behavior of martensitic stainless steels under thermomechanical conditions investigated the relationship between the microstructural changes and mechanical properties. In this review, grain formation under thermomechanical conditions and dynamic recrystallization behavior of this type of steel during the deformation phase is discussed.
The wall thickness eccentricity is one of the most important weaknesses that appears in seamless tubes production, since this imperfection is subsequently transferred downstream through the manufacturing stages until the final product. For this reason, in this article a finite element model of the rotary tube piercing (RTP) process is developed aimed at analysing the wall thickness eccentricity imperfection. Experimental data extracted from the industrial process is used for the validation of the model, including operational process variables like power consumption and process velocity, and deformation variables as elongation and longitudinal torsion, originated by axial and shear strain respectively. The cause of longitudinal torsion is also analysed. The two most important conclusions derived from this study are: (I) the longitudinal torsion of the tube is a crucial parameter for the correct model validation, and (II) the combined effect between the uneven temperature distribution of the billet and the plug bending deformation is identified as the major cause of the wall thickness eccentricity flaw.
This paper is aimed at modelling the flow behaviour of P91 steel at high temperature and a wide range of strain rates for constant and also variable strain-rate deformation conditions, such as those in real hot-working processes. For this purpose, an incremental physically-based model is proposed for the P91 steel flow behavior. This formulation considers the effects of dynamic recovery (DRV) and dynamic recrystallization (DRX) on the mechanical properties of the material, using only the flow stress, strain rate and temperature as state variables and not the accumulated strain. Therefore, it reproduces accurately the flow stress, work hardening and work softening not only under constant, but also under transient deformation conditions. To accomplish this study, the material is characterised experimentally by means of uniaxial compression tests, conducted at a temperature range of 900-1270 • C and at strain rates in the range of 0.005-10 s −1. Finally, the proposed model is implemented in commercial finite element (FE) software to provide evidence of the performance of the proposed formulation. The experimental compression tests are simulated using the novel model and the well-known Hansel-Spittel formulation. In conclusion, the incremental physically-based model shows accurate results when work softening is present, especially under variable strain-rate deformation conditions. Hence, the present formulation is appropriate for the simulation of the hot-working processes typically conducted at industrial scale.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.