No abstract

This paper introduces a cost-effective method for the fabrication of stretchable circuits on polydimethylsiloxane (PDMS) using inkjet printing of silver nanoparticle ink. The fabrication method, presented here, allows for the development of fully stretchable and wearable sensors. Inkjet-printed sinusoidal and horseshoe patterns are experimentally characterized in terms of the effect of their geometry on stretchability, while maintaining adequate electrical conductivity. The optimal fabricated circuit, with a horseshoe pattern at an angle of 45°, is capable of undergoing an axial stretch up to a strain of 25% with a resistance under 800 Ω. The conductivity of the circuit is fully reversible once it is returned to its pre-stretching state. The circuit could also undergo up to 3000 stretching cycles without exhibiting a significant change in its conductivity. In addition, the successful development of a novel inkjet-printed fully stretchable and wearable version of the conventional pulse oximeter is demonstrated. Finally, the resulting sensor is evaluated in comparison to its commercially available counterpart.

Purpose This review paper aims to introduce the inkjet printing as a tool for fabrication of flexible/wearable sensors. It summarizes inkjet printing techniques including various modes of operation, commonly used substrates and inks, commercially available inkjet printers and variables affecting the printing process. More focus is on the drop-on-demand printing mode, a strongly considered printing technique for patterning conductive lines on flexible and stretchable substrates. As inkjet-printed patterns are influenced by various variables related to its conductivity, resistivity, durability and dimensions of printed patterns, the main printing parameters (e.g. printing multilayers, inks sintering, surface treatment, cartridge specifications and printing process parameters) are reported. The embedded approaches of adding electronic components (e.g. surface-mounted and optoelectronic devices) to the stretchable circuit are also included. Design/methodology/approach In this paper, inkjet printing techniques for fabrication of flexible/stretchable circuits will be reviewed. Specifically, the various modes of operation, commonly used substrates and inks and variables affecting the printing process will be presented. Next, examples of inkjet-printed electronic devices will be demonstrated. These devices will be compared to their rigid counterpart in terms of ease of implementation and electrical behavior for wearable sensor applications. Finally, a summary of key findings and future research opportunities will be presented. Findings In conclusion, it is evident that the technology of inkjet printing is becoming a competitor to traditional lithography fabrication techniques, as it has the advantage of being low cost and less complex. In particular, this technique has demonstrated great capabilities in the area of flexible/stretchable electronics and sensors. Various inkjet printing methods have been presented with emphasis on their principle of operation and their commercial availability. In addition, the components of a general inkjet printing process have been discussed in details. Several factors affect the resulting printed patterns in terms of conductivity, resistivity, durability and geometry. Originality/value The paper focuses on flexible/stretchable optoelectronic devices which could be implemented in stretchable circuits. Furthermore, the importance and challenges related to printing highly conductive and highly stretchable lines, as well as reliable electronic devices, and interfacing them with external circuitry for power transmission, data acquisition and signal conditioning have been highlighted and discussed. Although several fabrication techniques have been recently developed to allow patterning conductive lines on a rubber substrate, the fabrication of fully stretchable wearable sensors remains limited which needs future research in this area for the advancement of wearable sensors.

No abstract

The fabrication and testing of spiral microchannels with a trapezoidal cross section for the passive separation of microparticles is reported in this article. In contrast to previously reported fabrication methods, the fabrication of trapezoidal spiral channels in glass substrates using a femtosecond laser is reported for the first time in this paper. Femtosecond laser ablation has been proposed as an accurate and fast prototyping method with the ability to create 3D features such as slanted-base channels. Moreover, the fabrication in borosilicate glass substrates can provide high optical transparency, thermal resistance, dimensional stability, and chemical inertness. Post-processing steps of the laser engraved glass substrate are also detailed in this paper including hydrogen fluoride (HF) dipping, chemical cleaning, surface activation, and thermal bonding. Optical 3D images of the fabricated chips confirmed a good fabrication accuracy and acceptable surface roughness. To evaluate the particle separation function of the microfluidic chip, 5 μm, 10 μm, and 15 μm particles were focused and recovered from the two outlets of the spiral channel. In conclusion, the new chemically inert separation chip can be utilized in biological or chemical processes where different sizes of cells or particles must be separated, i.e., red blood cells, circulating tumor cells, and technical particle suspensions.

Several research methodologies have recently been developed to allow for the patterning of conductive lines on elastomeric rubber substrates. Specifically, various conductive materials, substrates, and fabrication techniques were investigated to develop stretchable circuits. One promising technique recommends the application of axial strain on an elastomer substrate prior to patterning conductive lines on it. When the substrate is released, conductive lines buckle to form waves, making the circuit stretchable. However, the majority of applications of stretchable circuits require fitting them to two-dimensional surfaces, such as the human body. Hence, in this paper we propose the concept of radial pre-stretching of the substrates to enhance the stretchability of the fabricated circuits. In particular, straight silver conductive lines were deposited on a polydimethylsiloxane (PDMS) surface using inkjet printing technology, and subsequently tested under both axial and radial loads. Radial pre-stretching was compared to axial pre-stretching, resulting in an improved performance under radial loads. The optimal performance was achieved by pre-stretching the PDMS substrate with a radial strain of 27%. This resulted in stretchable circuits which could sustain radial loads with an average breakdown strain of approximately 19%. Additionally, horseshoe patterns were printed on radially pre-stretched PDMS substrates and their performance was compared to that of their straight line counterparts. Though these patterns are generally favorable for the fabrication of stretchable circuits, the optimal horseshoe pattern examined in this study could only sustain up to 16% radial strain on average when radially pre-stretched by 27%.

This paper presents the applicability of a microtechnologically fabricated microbubble column as a screening tool for submerged aerobic cultivation. Bubbles in the range of a few hundred micrometers in diameter were generated at the bottom of an upright-positioned microdevice. The rising bubbles induced the circulation of the liquid and thus enhanced mixing by reducing the diffusion distances and preventing cells from sedimentation. Two differently sized nozzles (21 × 40 µm(2) and 53 × 40 µm(2) in cross-section) were tested. The gas flow rates were adjustable, and the resulting bubble sizes and gas holdups were investigated by image analysis. The microdevice features sensor elements for the real-time online monitoring of optical density and dissolved oxygen. The active aeration of the microdevice allowed for a flexible oxygen supply with mass transfer rates of up to 0.14 s(-1). Slightly higher oxygen mass transfer rates and a better degassing were found for the microbubble column equipped with the smaller nozzle. To validate the applicability of the microbubble column for aerobic submerged cultivation processes, batch cultivations of the model organism Saccharomyces cerevisiae were performed, and the specific growth rate, oxygen uptake rate, and yield coefficient were investigated.

The respiration rate (RR) is a key vital sign that links to adverse clinical outcomes and has various important uses. However, RR signals have been neglected in many clinical practices for several reasons and it is still difficult to develop low-cost RR sensors for accurate, automated, and continuous measurement. This study aims to fabricate, develop and evaluate a novel stretchable and wearable RR sensor that is low-cost and easy to use. The sensor is fabricated using the soft lithography technique of polydimethylsiloxane substrates (PDMS) for the stretchable sensor body and inkjet printing technology for creating the conductive circuit by depositing the silver nanoparticles on top of the PDMS substrates. The inkjet-printed (IJP) PDMS-based sensor was developed to detect the inductance fluctuations caused by respiratory volumetric changes. The output signal was processed in a Wheatstone bridge circuit to derive the RR. Six different patterns for a IJP PDMS-based sensor were carefully designed and tested. Their sustainability (maximum strain during measurement) and durability (the ability to go bear axial cyclic strains) were investigated and compared on an automated mechanical stretcher. Their repeatability (output of the sensor in repeated tests under identical condition) and reproducibility (output of different sensors with the same design under identical condition) were investigated using a respiratory simulator. The selected optimal design pattern from the simulator evaluation was used in the fabrication of the IJP PDMS-based sensor where the accuracy was inspected by attaching it to 37 healthy human subjects (aged between 19 and 34 years, seven females) and compared with the reference values from e-Health nasal sensor. Only one design survived the inspection procedures where design #6 (array consists of two horseshoe lines) indicated the best sustainability and durability, and went through the repeatability and reproducibility tests. Based on the best pattern, the developed sensor accurately measured the simulated RR with an error rate of 0.46 ± 0.66 beats per minute (BPM, mean ± SD). On human subjects, the IJP PDMS-based sensor and the reference e-Health sensor showed the same RR value, without any observable differences. The performance of the sensor was accurate with no apparent error compared with the reference sensor. Considering its low cost, good mechanical property, simplicity, and accuracy, the IJP PDMS-based sensor is a promising technique for continuous and wearable RR monitoring, especially under low-resource conditions.