No abstract

No abstract

Mineral carbonation, involving reactions of alkaline earth oxides with CO2, has received great attention, as a potential carbon dioxide sequestration technology. Indeed, once converted into mineral carbonate, CO2 can be permanently stored in an inert phase. Several studies have been focalized to the utilization of industrial waste as a feedstock and the reuse of some by-products as possible materials for the carbonation reactions. In this work municipal solid waste incineration fly ash and other ashes, as bottom ash, coal fly ash, flue gas desulphurization residues, and silica fume, are stabilized by low-cost technologies. In this context, the CO2 is used as a raw material to favor the chemical stabilization of the wastes, by taking advantage of the pH reduction. Four different stabilization treatments at room temperature are performed and the carbonation reaction evaluated for three months. The crystalline calcium carbonate phase was quantified by the Rietveld analysis of X-ray diffraction (XRD) patterns. Results highlight that the proposed stabilization strategy promotes CO2 sequestration, with the formation of different calcium carbonate phases, depending on the wastes. This new sustainable and promising technology can be an alternative to more onerous mineral carbonation processes for the carbon dioxide sequestration.

This review paper reports a detailed characterization of some combustion or incineration residues and by-products produced in a medium-sized city in Northern Italy. The municipal solid waste incineration (MSWI) generates fly ash, which is a toxic waste. Coal fly ash (CFA) and flue gas desulfurization (FGD) derive from the thermoelectric coal plant located in the same city. Along with these ashes, silica fume and rice husk ash are also considered for the stabilization of fly ash based on their amorphous silica content with the aim to convert them into an inert material. The characterization of all the investigated ashes was performed using different techniques: X-ray diffraction, total reflection X-ray fluorescence, scanning electron microscopy, and transmission electron microscopy. The aim of this work is to describe the reuse possibilities that were proposed for these ashes, which were determined also on the basis of their structural properties. Several possible applications of the investigated ashes are proposed, and the most suitable reuse of stabilized fly ash samples seems to be the production of sustainable plastic composites. This paper shows that the reuse of the by-product materials can allow natural resources to be preserved following the principles of a circular economy.

Rice husk poultry litter ash (RHPLA) is proposed as a valuable secondary source to recover phopshorus and amorphous silica in three steps.

This work reports and analyzes the mechanical properties of some composites obtained using stabilized waste with epoxy resins E-227. For comparison, correspondent composite samples were realized using calcite as a filler. The recovered stabilized waste was obtained by means of a new method to stabilize municipal solid waste incineration (MSWI) fly ash (FA), based on the use of bottom ash (BA). The aim of this paper is to show that the stabilization process, which can be considered a zero—waste treatment, produces inert materials, that can be reused as a filler. The production of new filler was made on a pilot plant, designed to verify the transferability of the proposed stabilization technology. Mechanical analysis revealed that flexural modulus raises by increasing the filler content around 30% wt, independently of filler type, stabilized sample or calcium carbonate. Mechanical properties are lower in the samples with the high amount of filler due to the crowding effect. The morphology of composite materials showed a non-homogeneous dispersion of particles in stabilized sample filler, characterized by large particle agglomerates. Finally, according to the ESCAPE simplified method, the obtained composites result more sustainable in comparison with the corresponding ones produced by using natural resources (like calcite). These findings open new possibilities for the reuse of the stabilized material, in frame of circular economy principles, with environmental and economic advantages.

No abstract

This work reports on qualitative and semi-quantitative elemental analysis of particulate matter (PM) collected on PTFE membrane filters, for a source apportionment study conducted in Brescia (Italy). Sampling was undertaken in a residential area where an increase in Mn emissions has been highlighted by previous studies. Filters are measured by means of X-ray Fluorescence (XRF) based techniques such as micro-XRF and grazing incidence XRF using synchrotron radiation, Mo or W excitation sources, after applying an automatized sample preparation method. A heterogeneous distribution in PM shape, size and composition was observed, with features typical of anthropogenic sources. XRF measurements performed at various incidence angle, on large areas and different experimental setup were reproducible. The results demonstrate a successful comparison of the various XRF instrumentation, and the decrease in Mn content with the distance away from the identified emission source. This work highlights the potentialities of the presented approach to provide a full quantitative analysis, and ascertain its suitability for providing a direct, fast, simple and sensitive elemental analysis of filters in source apportionment studies and screening purposes.