In this topical review, the recent progress on radiation-hardened fiber-based technologies is detailed, focusing on examples for space applications. In the first part of the review, we introduce the operational principles of the various fiber-based technologies considered for use in radiation environments: passive optical fibers for data links, diagnostics, active optical fibers for amplifiers and laser sources as well as the different classes of point and distributed fiber sensors: gyroscopes, Bragg gratings, Rayleigh, Raman or Brillouin-based distributed sensors. Second, we describe the state of the art regarding our knowledge of radiation effects on the performance of these devices, from the microscopic effects observed in the amorphous silica glass used to design fiber cores and cladding, to the macroscopic response of fiber-based devices and systems. Third, we present the recent advances regarding the hardening (improvement of the radiation tolerance) of these technologies acting on the material, device or system levels. From the review, the potential of fiber-based technologies for operation in radiation environments is demonstrated and the future challenges to be overcome in the coming years are presented.
International audienceWe demonstrate that a porous film of silica nanoparticles emits a bright visible luminescence associated with defects stabilized by oxygen chemisorption at oxygen deficient center sites. Time-resolved spectra excited by a tunable laser allow us to distinguish the luminescence at 1.99 eV, characteristic of the nonbridging oxygen hole center (NBOHC) (Si-O)3 Si-O*, and a fast and a slow emission: the first (lifetime τ ≈ 25 ns) is peaked at 2.27 eV with an excitation spectrum centered at 5.5 eV; the second (τ ≈ 7.5 μs) is peaked at 2.41 eV and is excited around 3.2 and 5.2 eV. Reaction in an air atmosphere leads to the disappearance of the NBOHC luminescence and of the fast band, whereas the slow one remains stable. On the basis of the comparison with previous experimental and computational works, we discuss the role of the silanone SidO and of the dioxasilyrane Si(O2) as the emitting defects
We report a method for fabricating fiber Bragg gratings (FBG) resistant to very severe environments mixing high radiation doses (up to 3 MGy) and high temperatures (up to 230°C). Such FBGs have been written in two types of radiation resistant optical fibers (pure-silica and fluorine-doped cores) by exposures to a 800 nm femtosecond IR laser at power exceeding 500 mW and then subjected to a thermal annealing treatment of 15 min at 750°C. Under radiation, our study reveals that the radiation induced Bragg wavelength shift (BWS) at a 3 MGy dose is strongly reduced compared to responses of FBGs written with nonoptimized conditions. The BWS remains lower than 10 pm for temperatures of irradiation ranging from 25°C to 230°C without noticeable decrease of the FBG peak amplitude. For an applicative point of view, this radiation induced BWS corresponds to an additional error on the temperature measurements lower than 1.5°C, opening the way to the development of radiation-tolerant multi-point temperature sensors for nuclear industry.
Optical fibers hold promise for accurate dosimetry in small field proton therapy due to their superior spatial resolution and the lack of significant Cerenkov contamination in proton beams. One known drawback for most scintillation detectors is signal quenching in areas of high linear energy transfer, as is the case in the Bragg peak region of a proton beam. In this study, we investigated the potential of innovative optical fiber bulk materials using the sol-gel technique for dosimetry in proton therapy. This type of glass is made of amorphous silica (SiO) and is doped with Gd ions and possesses very interesting light emission properties with a luminescence band around 314 nm when exposed to protons. The fibers were manufactured at the University of Lille and tested at the TRIUMF Proton Therapy facility with 8.2–62.9 MeV protons and 2–6 nA of extracted beam current. Dose-rate dependence and quenching were measured and compared to other silica-based fibers also made by sol-gel techniques and doped with Ce and Cu. The three fibers present strong luminescence in the UV (Gd) or visible (Cu,Ce) under irradiation, with the emission intensities related directly to the proton flux. In addition, the 0.5 mm diameter Gd-doped fiber shows superior resolution of the Bragg peak, indicating significantly reduced quenching in comparison to the Ce and Cu fibers with a Birks’ constant, k, of (0.0162 0.0003) cm/MeV in comparison to (0.0333 0.0006) cm/MeV and (0.0352 0.0003) cm/MeV, respectively. To our knowledge, this is the first report of such an interesting k for a silica-based optical fiber material, showing clearly that this fiber presents lower quenching than common plastic scintillators. This result demonstrates the high potential of this inorganic fiber material for proton therapy dosimetry.
International audienceWe investigate the response of Ge-doped, P-doped, pure-silica, or Fluorine-doped fibers to extreme environments combining doses up to MGy(SiO $_{{{2}}}$) level of 10 keV X-rays and temperatures between 25 C and 300 C . First, we evaluate their potential to serve either as parts of radiation tolerant optical or optoelectronic systems or at the opposite, for the most sensitive ones, as punctual or distributed dosimeters. Second, we improve our knowledge on combined ionizing radiations and temperature (R&T) effects on radiation-induced attenuation (RIA) by measuring the RIA spectra in the ultraviolet and visible domains varying the R&T conditions. Our results reveal the complex response of the tested fibers in such mixed environments. Increasing the temperature of irradiation increases or decreases the RIA values measured at 25C or sometimes has no impact at all. Furthermore, R&T effects are time dependent giving an impact of the temperature on RIA that evolves with the time of irradiation. The two observed transient and stationary regimes of temperature influence will make it very difficult to evaluate sensor vulnerability or the efficiency of hardening approaches without extensive test campaign
We investigated point defects induced in rad-hard Fluorine-doped optical fibers using both a mixed source of neutrons (fluences from 1015 to 1017 n/cm2) and γ-rays (doses from 0.02 to 2 MGy) and by a γ-ray source (dose up to 10 MGy). By combining several complementary spectroscopic techniques such as radiation-induced attenuation, confocal micro-luminescence, time-resolved photo-luminescence and electron paramagnetic resonance, we evidenced intrinsic and hydrogen-related defects. The comparison between the two irradiation sources highlights\ud close similarities among the spectroscopic properties of the induced defects and the linear correlation of their concentration up to 1016 n/cm2. These results are interpreted on the basis of the generation processes of defects from precursors sites, that are common to both γ-rays and neutrons. In contrast, the highest neutron fluence (1017 n/cm2) causes peculiar effects, such as the growth of a photoluminescence and variations of the spectral and decay properties of the emission related with nonbridging oxygen hole centers, that are likely due to silica network modification
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
334 Leonard St
Brooklyn, NY 11211
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.