The molar mass distribution of a polymer sample is a critical determinant of its material properties and is generally analyzed by gel permeation chromatography or more recently, by MALDI-TOF mass spectrometry. We describe here a novel method for the determination of the degree of polymerization of polydisperse, uncharged, water-soluble polymers (e.g., poly(ethylene glycol) (PEG)), based upon single-monomer resolution of DNA-polymer conjugates by free-solution capillary electrophoresis. This is accomplished by end-on covalent conjugation of a polydisperse, uncharged polymer sample (PEG) to a monodisperse, fluorescently labeled DNA oligomer, followed by electrophoretic analysis. The monodisperse, charged DNA "engine" confers to each conjugate an equal amount of electromotive force, while the varying contour lengths of the uncharged, polydisperse polymers engender different amounts of hydrodynamic drag. The balance of electromotive and hydrodynamic forces enables rapid, high-resolution separation of the DNA-polymer conjugates as a function of the size of the uncharged PEG tail. This provides a profile of the molar mass distribution of the original polymer sample that can be detected by laser-induced fluorescence through excitation of the dye-labeled DNA. We call this method free solution conjugate electrophoresis (FSCE). Theory-based analysis of the resulting electrophoresis data allows precise calculation of the degree of polymerization of the PEG portion of each conjugate molecule. Knowledge of the molecular mass of the uncharged polymer's repeat unit allows for direct calculation of the molar mass averages as well as sample polydispersity index. The results of these analyses are strikingly reminiscent of MALDI-TOF spectra taken of the same PEG samples. PEG samples of 3.4-, 5-, and 20-kDa nominal average molar mass were analyzed by FSCE and MALDI-TOF; the values of the molar mass averages, Mw and Mn, typically agree to within 5%. Measurements and molar mass calculations are performed without any internal standards or calibration. Moreover, when DNA-polymer conjugate analysis is performed in a chip-based electrophoresis system, separation is complete in less than 13 min. FSCE offers an alternative to MALDI-TOF for the characterization of uncharged, water-soluble polymers that can be uniquely conjugated to DNA.
Multiwavelength detection of laser induced fluorescence for dideoxynucleotide DNA sequencing with four different fluorophores and separation by capillary gel electrophoresis is described. A cryogenically cooled, low readout noise, 2-dimensional charge-coupled device is used as a detector for the on-line, on-column recording of emission spectra. The detection system has no moving parts and provides wavelength selectivity on a single detector device. The detection limit of fluorescently labeled oligonucleotides meets the high sensitivity requirements for capillary DNA sequencing largely due to the efficient operation of the CCD detector with a 94% duty cycle. Using the condition number as a selectivity criterion, multiwavelength detection provides better analytical selectivity than detection with four bandpass filters. Monte Carlo studies and analytical estimates show that base assignment errors are reduced with peak identification based on entire emission spectra. High-speed separation of sequencing samples and the treatment of the 2-dimensional electropherogram data is presented. Comparing the DNA sequence of a sample separated by slab gel electrophoresis with sequence from capillary gel electrophoresis and multiwavelength detection we find no significant difference in the amount of error attributable to the instrumentation.
Rapid, high-resolution separation of DNA sequencing fragments by capillary gel electrophoresis using an automated, commercially available instrument is presented. The effect of column lengths and electric field strength on the resolution of sequencing fragments as well as the sensitivity of laser-induced fluorescence (LIF) detection was investigated. Using a short capillary of 20 cm length, which results in a U-shape of the capillary in the capillary cartridge, very high separation efficiency, up to 17 x 10(6) theoretical plates per m, is obtained. Analysis of the band broadening factors revealed that the resolution on the short column is predominantly determined by axial diffusion and to a minor extent by detection zone width. Presumably due to the coiling of longer capillaries in the capillary cartridge, increasing the capillary length does not increase the separation efficiency as predicted for diffusion-limited separation. The concentration limit of detection (signal-to-noise ratio = 2) is 0.2 x 10(-12) M of fluorescein-labeled oligonucleotide primer under the separating conditions for DNA sequencing samples. Increasing the electric field strength from 100 to 175 V/cm improved resolution and at the same time approximately doubled the sequencing speed. Fragments up to 500 nucleotides in length are resolved in less than 50 min.
A cryogenically cooled charge-coupled device (CCD) camera equipped with an area CCD array is used in a line scanning system for low-light-level imaging of chemiluminescent DNA sequencing blots. Operating the CCD camera in time-delayed integration (TDI) mode results in continuous data acquisition independent of the length of the CCD array. Scanning is possible with a resolution of 1.4 line pairs/mm at the 50% level of the modulation transfer function. High-sensitivity, low-light-level scanning of chemiluminescent direct-transfer electrophoresis (DTE) DNA sequencing blots is shown. The detection of DNA fragments on the blot involves DNA-DNA hybridization with oligonucleotide-alkaline phosphatase conjugate and 1,2-dioxetane-based chemiluminescence. The width of the scan allows the recording of up to four sequencing reactions (16 lanes) on one scan. The scan speed of 52 cm/h used for the sequencing blots corresponds to a data acquisition rate of 384 pixels/s. The chemiluminescence detection limit on the scanned images is 3.9 x 10(-18) mol of plasmid DNA. A conditional median filter is described to remove spikes caused by cosmic ray events from the CCD images.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.