Aim:The null hypothesis is that there is no difference in the post-operative antiinflammatory efficacy of chlorhexidine (CHX), 2% saline rinses (SR) and a herbal mouthwash (MW) after non-surgical mechanical debridement (MD) for treatment of peri-implant mucositis (PiM). The aim was to compare the post-operative antiinflammatory efficacy of CHX, 2% SR and a herbal oral rinse after non-surgical MD of PiM.
Materials and Methods:The present randomized controlled trial had a single-blinded parallel arm design. Patients diagnosed with PiM were enrolled. Demographic information was recorded. All patients underwent MD and were randomly divided into 4 groups: CHX-group: 0.12% non-alcoholic CHX; Sodium chloride (NaCl) group: 2% NaCl rinses; Herbal MW group: Herbal-based MW and H 2 O group: distilled water with peppermint flavour. After MD, all the participants were advised to rinse twice daily (every 12 hrs) for 2 weeks with their respective MWs. In all groups, peri-implant modified plaque index (mPI), modified gingival index (mGI) and probing depth (PD) were measured at baseline and at 12 weeks of follow-up. Sample size was estimated using data from a pilot investigation; and group-comparisons were performed. Statistical significance was confirmed when P-values were below 0.01.Results: Sixty individuals (15 patients/group) were included. At baseline, mPI, mGI and PD were comparable in all groups. At baseline, there was no significant difference in peri-implant mPI, mGI and PD in all groups. At 12-weeks' follow-up, there was a statistically significant reduction in peri-implant mPI (p < 0.01), mGI (p < 0.01) and PD (p < 0.01) in CHX, NaCl and herbal MW groups compared with H 2 O group. There was no significant relation between implant location, duration for which, implants were functional, gender and peri-implant clinical parameters in all groups.
Conclusion:After non-surgical MD, post-operative use of CHX and herbal and NaCl MWs is useful for the management of PiM in the short-term.
Excessive gingival display is a common clinical presentation that often requires surgical intervention. This report is for a patient for whom esthetic crown lengthening is indicated due to altered passive eruption. Cone beam computed tomography (CBCT) scan and an intraoral scan were used to design and print a single surgical guide which provided a reference for both gingivectomy and osteoectomy. A satisfactory outcome was obtained 6 months after surgery. The present technique provided a simplified method of generating a surgical guide with predictable results by relying on the existing tooth anatomy rather than diagnostic waxing. This technique is particularly useful when crowns or veneers are not indicated.
The effect of printing parameters on the surface characteristics of three-dimensional (3D)-printed denture base resins (DBRs) is neglected. Therefore, this study investigated the effect of printing orientation and post-curing time on the surface roughness and hardness. One conventional heat-polymerized (HP) resin and two 3D-printing resins (NextDent (ND) and ASIGA (AS)) were used to fabricate a total of 250-disc (10 × 2.5 mm) specimens. ND and AS specimens were printed with different orientations (0-, 45-, and 90-degree) and each orientation group was subjected to four post-curing times (30, 60, 90, 120 min). Printed specimens were thermo-cycled (10,000 cycles) followed by the measuring of surface roughness (Profilometer (Ra)) and hardness (a Vickers hardness (VH)). ANOVA and post hoc tests were used for data analysis (α = 0.05) at significant levels. AS and ND showed no significant changes in Ra when compared with HP (p ˃ 0.05), except the 45-degree orientation (AS/90 min and AS/120 min) significantly increased surface roughness (p ˂ 0.001). There was no significant difference in Ra with different orientations and post-curing time for both materials AS and ND (p ˃ 0.05). Compared with HP, 3D-printed DBRs showed low VH values (p ˂ 0.001). For AS, 90-degree orientation showed a significant decrease in VH at 60, 90, and 120 min when compared with 0- and 45-degree orientation (p ˂ 0.001), while ND showed no significant difference in VH with different printing orientations (p ˃ 0.05). The VH of AS and ND improved when increasing post-curing time to 120 min (p ˂ 0.001), and the printing orientations and post-curing time did not affect the Ra of 3D-printed DBRs.
Studies showed an enhancement in the quality of life in many patients who have been treated with oral appliances, and patients in general prefer oral appliances over CPAP therapy or any other treatments for OSA because of its convenience.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.