In the framework of the DEMOnstration fusion power plant (DEMO) design coordinated by the EUROfusion consortium, a pre-conceptual design of the superconducting magnet system has been developed. For the toroidal field coils (TFCs), three winding pack (WP) options have been proposed; exploring different winding approaches (pancakes vs. layers), and manufacturing techniques (react & wind vs. wind & react Nb 3 Sn). Thermal-hydraulic and mechanical analyses on the three WPs have produced encouraging results, with some critical issues to be solved in future studies and optimizations. The experimental tests on TF prototype short sample conductors have demonstrated a limited performance degradation with electromagnetic cycles and significantly lower effective strains than most of the large-size Nb 3 Sn conductors reported in literature. The toroidal field quench protection circuit has been studied, starting from different topologies and focusing on the most promising one. Two designs are also presented for the central solenoid magnet, with preliminary evaluations on the AC losses during the plasma breakdown. Finally, the design of a TF winding pack based on HTS conductors and the experimental tests on "fusion-relevant" HTS cables are illustrated.
The DEMO reactor is expected to be the first application of fusion for electricity generation in the near future. To this aim conceptual design activities are progressing in Europe (EU) under the lead of the EUROfusion Consortium in order to drive on the development of the major tokamak systems. In 2014 the activities carried out by the magnet system project team were focused on the Toroidal Field (TF) magnet system design and demonstrated major achievements in terms of concept proposals and of consolidated evaluations against design criteria. Several magnet system R&D activities were conducted in parallel, together with broad investigations on High Temperature Superconductor (HTS) technologies. In this paper we present the outcomes of the work conducted in two areas in the 2014 magnet work program: (1) the EU inductive reactor (called DEMO1) 2014 configuration (power plant operating under inductive regime) was the basis of conceptual design activities, including further optimizations; and (2) the HTS R&D activities building upon the consolidated knowledge acquired over the past years
Works on bending strain in Nb 3 Sn wires were initiated in support of the 'react-and-wind' technique used to manufacture superconducting coils. More recently, the bending strains of Nb 3 Sn strands in cable-in-conduit conductors (CICC) under high Lorentz forces have been thought to be partly responsible for the degradation of the conductor performance in terms of critical current and n index, particularly for the international thermonuclear experimental reactor (ITER) conductors. This has led to a new wave of experiments and modelling on this subject. The computation of the current transport capability in an Nb 3 Sn wire under uniform bending used to be carried out through the so-called Ekin's models, and more recently through numerical simulations with electric networks. The flaws of Ekin's models are that they consider only two extreme cases or limits, namely the so-called long twist pitch (LTP) or short twist pitch (STP) cases, and that these models only allow computation of a value for the critical current without reference to the n index of the superconducting filaments (i.e. this index is implicitly assumed to be infinite). Although the numerical models allow a fine description of the wire under operation and can take into account the filament's n index, they need a refined meshing to be accurate enough and their results may be sensitive to boundary conditions (i.e. current injection in the wire), also general intrinsic parameters cannot be easily identified. In this paper, we propose clearly to go further than Ekin's models by developing, from a homogeneous model and Maxwell's equations, an analytical model to establish the general equation governing the evolution of the electric field inside an Nb 3 Sn strand under uniform bending (with possible longitudinal strain). Within the usual strand fabrication limits, this equation allows the definition of one single parameter to discriminate the STP and LTP cases. It is also shown that whereas Ekin's LTP model corresponds well to a limiting solution of the problem when the transverse resistivity tends toward zero (or the twist pitch tends towards infinity), Ekin's STP model must be modified (improved) when the filament's n index is finite. Since the general equation cannot be solved analytically, we start from the LTP model and develop a first order correction to be applied when the transverse resistivity, the twist pitch and the filament's n index are finite. Using a simple but realistic law for depicting the strain dependence of the critical current density in the Nb 3 Sn filaments, we can fully compute the corrected expression and give the result under a general analytical formula for a strand submitted to both bending and compressive/tensile strains. The results are then compared in two different cases with those obtained with the numerical code CARMEN (based on an electrical network) developed at CEA. Last, a semi-empirical formula has been developed to evolve continuously from the LTP limit to the improved STP limit when the transverse resistivity evolves ...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.