This article describes the results of optimization of the colloidal photonic crystal opal films deposition by means of atomic force microscopy investigation. The main factors affecting the quality of the colloidal opal films are studied. Bragg diffraction occurs in the periodic distribution of colloidal microspherical particles, and ordered structure is critical for formation of the photonic band gap. It is found that polystyrene opal structures obtained in optimal conditions have a good periodicity, uniformity, and high packing density.
Детали типа валов и их комбинации с дисками являются важнейшими элементами конструкции современного газо-турбинного двигателя для авиадвигателей и аналогичных наземных энергетических установок. Эти детали эксплуа-тируются в условиях экстремальных силовых и тепловых воздействий и, поэтому, изготавливаются из жаропроч-ных сплавов на основе никеля, железа и титана. Формообразование подобных деталей традиционными методами горячей объемной штамповки требует использования мощного, энергоемкого оборудования. Одним из наиболее перспективных способов снижения энергосиловых затрат на изготовление осесимметричных деталей авиационного назначения, снижения количества переходов и увеличения КИМ является изотермическая раскатка в состоянии сверхпластичности на специализированных раскатных станах. Для проектирования данного класса оборудования необходимо определение энергосиловых параметров, которые это оборудование должно обеспечить. Для определе-ния необходимых энергосиловых параметров технологического процесса эффективным способом является мате-матическое моделирование. В настоящей статье предложена методика создания конечно-элементной модели техно-логического процесса изотермической раскатки в состоянии сверхпластичности при высокой степени локализации пластической деформации, с учетом механических свойств материала с ультра мелкозернистой структурой на при-мере производства диска из жаропрочного титанового сплава ВТ9. В работе приведены как результаты конечно-эле-ментного расчета энергосиловых параметров процесса раскатки в коммерческом программном коде DEFORM 3D, так и результаты экспериментального измерения сил деформирования при раскатке. Parts like shafts and their combinations with discs are very significant elements of the modern aviation gas turbine engines and cognate ground energy propulsions. These parts are usually working in the extremely high loading and temperature conditions and therefore are produced from the highly heat-resistant alloys on the base of Ni, Fe and Ti. The production of these parts with the traditional hot metal forming leads the need of using powerful and energy-consuming equipment. One of the most prospective ways of reducing the load-energy consumption, reducing of the technological operations quantities, increasing of the material efficiency in producing of the axisymmetric aircraft parts is isothermal rolling under the superplastic deformation (SPD) condition using the specialized rolling machines. For the design of this type of machines it is necessary to estimate the load stroke parameters of the process, which the machine has to provide. The effective method of the estimation of the required load stroke parameters is computer simulation of the rolling process. In this paper, the technique to create a finite element model of the process of SPD during isothermal rolling with a high degree of plastic deformation localization is presented and exemplified by the production of disc made of heat-resistant VT9 titanium alloy, in respect to the mechanical properties of the ultra fine grain mat...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.