No abstract

A method of solution is described in which the governing equation is modified to account for variations in the oil-film thickness in the axial direction owing to journal misalignment. The position of the journal is specified by means of its eccentricity at its mid-length and by two parameters defining the extent and direction of the misalignment. The pressure distribution is evaluated numerically, and the direct load, friction torque, oil flow, and couple arising from the misalignment of the journal are obtained by numerical integration. A full range of journal misalignment conditions is examined for two length-diameter ratios. Results are presented in the form of non-dimensionalized graphs, showing the variation of direct load and misalignment couple with the journal misalignment parameters described. The angle between the line of action of the misalignment couple and the load line is evaluated in each instance, and graphs are presented to show the variation of the performance parameters for a particular degree of misalignment with the direction of application of the couple. Results for the particular instances in which the couple is in line with or at right angles to the load line are extracted, and these are compared with published experimental results of other workers. Good agreement is obtained, and moreover it is shown that, in general, these are not the two extremes of misalignment. For these two conditions design charts are presented, whereby, from knowledge of the applied couple and direct load, the degree of misalignment and the resultant peak pressure parameter may be determined. Charts which illustrate the reduction in load capacity for a particular journal misalignment in the plane of the load are also presented. General validity is claimed for this method of exploring a relatively unexamined subject, and the results are considered by the authors to be a useful improvement on those obtained by previous analytical workers.

A mathematical model for predicting spline coupling induced nonsynchronous rotor vibrations is developed, and the predictions are compared with data from a rotor dynamics test rig. The special feature of the spline model is the characterization of the friction forces that are produced at the mating spline teeth surfaces and subsequent calculation of the internal damping coefficients. The spline internal damping and the r esulting rotor instabilities are predicted for four different spline configurations and the solution results are correlated with measured data from a gas turbine rotor simulator test rig.

The U.S. natural gas pipeline industry is facing the twin challenges of increased flexibility and capacity expansion. To meet these challenges, the industry requires improved choices in gas compression to address new construction and enhancement of the currently installed infrastructure. The current fleet of installed reciprocating compression is primarily slow-speed integral machines. Most new reciprocating compression is and will be large, highspeed separable units.The major challenges with the fleet of slow-speed integral machines are: limited flexibility and a large range in performance. In an attempt to increase flexibility, many operators are choosing to single-act cylinders, which are causing reduced reliability and integrity. While the best performing units in the fleet exhibit thermal efficiencies between 90% and 92%, the low performers are running down to 50% with the mean at about 80%. The major cause for this large disparity is due to installation losses in the pulsation control system. In the better performers, the losses are about evenly split between installation losses and valve losses.The major challenges for high-speed machines are: cylinder nozzle pulsations, mechanical vibrations due to cylinder stretch, short valve life, and low thermal performance. To shift nozzle pulsation to higher orders, nozzles are shortened, and to dampen the amplitudes, orifices are added. The shortened nozzles result in mechanical coupling with the cylinder, thereby, causing increased vibration due to the cylinder stretch mode. Valve life is even shorter than for slow speeds and can be on the order of a few months. The thermal efficiency is 10% to 15% lower than slow-speed equipment with the best performance in the 75% to 80% range.The goal of this advanced reciprocating compression program is to develop the technology for both high speed and low speed compression that will expand unit flexibility, increase thermal efficiency, and increase reliability and integrity.Retrofit technologies that address the challenges of slow-speed integral compression are: (1) optimum turndown using a combination of speed and clearance with single-acting operation as a last resort; (2) if single-acting is required, implement infinite length nozzles to address nozzle pulsation and tunable side branch absorbers for 1x lateral pulsations; and (3) advanced valves, either the semi-active plate valve or the passive rotary valve, to extend valve life to three years with half the pressure drop. This next generation of slow-speed compression should attain 95% efficiency, a three-year valve life, and expanded turndown.New equipment technologies that address the challenges of large-horsepower, high-speed compression are: (1) optimum turndown with unit speed; (2) tapered nozzles to effectively reduce nozzle pulsation with half the pressure drop and minimization of mechanical cylinder stretch induced vibrations; (3) tunable side branch absorber or higher-order filter bottle to address lateral piping pulsations over the entire extended speed range w...

During the aerobic growth of Streptococcus faecalis strain 10C1, with limiting levels of glucose as the substrate, a molar growth yield (Y) of 58.2 g (dry weight) per mole of glucose was obtained. Under these conditions of growth, glucose was dissimilated primarily to acetate and CO 2 . The incorporation of 14 C-glucose into cell material was no greater under aerobic conditions than during anaerobic growth. Assuming an adenosine triphosphate coefficient of 10.5, the aerobic Y cannot be explained solely on the basis of substrate phosphorylation and would appear to substantiate previous enzymatic evidence for oxidative phosphorylation in this cytochromeless species. With mannitol as the substrate, an aerobic Y of 64.6 was obtained. Extracts of mannitol-grown cells contained a nicotinamide adenine dinucleotide (NAD)-linked mannitol-1-phosphate (M-1-P) dehydrogenase. The difference in aerobic Y values with mannitol and glucose as substrates would indicate that the in vivo P/O ratio from the oxidation of reduced NAD generated by the oxidation of M-1-P approximates 0.6. The Y values with pyruvate and glycerol as substrates under aerobic conditions were 15.5 and 24.7, respectively.