Wetting and joining of surface-oxidized SiC ceramic with calcium lithium aluminosilicate glass filler

Fang, Jian; Sun, Liangbo; Guo, Songsong; Shan, Tipeng; Wen, Yue; Liu, Chunfeng; Zhang, Jie

doi:10.1016/j.apsusc.2021.150951

Cited by 13 publications

(2 citation statements)

References 45 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…15 In addition, ZrSi 2 is considered as a candidate material for nuclear energy application due to its low neutron cross-section. 16 However, the difference in thermal expansion coefficient between ZrSi 2 (8.3 × 10 −6 / • C) 17 and SiC (4 × 10 −6 / • C) 18 ceramics could lead to the generation of a high residual stress in the joint after cooling, which potentially weakens the mechanical performance of the joint. Generally, materials with low thermal expansion coefficient can be added to reduce the thermal expansion coefficient mismatch between the interlayer and the substrate [19][20][21] in order to improve the joint performance.…”

Section: Introductionmentioning

confidence: 99%

Joining SiC ceramics with ZrSi₂–SiC filler at low temperatures

Zhu,

Jian,

Tan

et al. 2024

J Am Ceram Soc.

View full text Add to dashboard Cite

ZrSi2–SiC powder was employed as the joining material to join SiC ceramics in this study. The effects of SiC particle (SiCp) content and joining temperature on the phase composition, microstructure, and shear strength of SiC joints were studied and reported for the first time. Research results showed that introduction of SiCp into the interlayer improved the mechanical performance of the joint. When 10 wt.% SiCp was introduced into the interlayer, the optimal shear strength measured of the joint was 116.7 ± 6.7 MPa under the joining condition of 1500°C for 10 min. With the joining temperature increased, the shear strength of the joint gradually increases. When the joint was performed at 1600°C for 10 min, an ultra‐high temperature phase of ZrC was detected in the interlayer, and the shear strength of the joint was 168.1 ± 12.6 MPa. The SiC joint with high mechanical strength might have the potential for application in the field of nuclear industry.

show abstract

Section: Introductionmentioning

confidence: 99%

Joining SiC ceramics with ZrSi₂–SiC filler at low temperatures

Zhu,

Jian,

Tan

et al. 2024

J Am Ceram Soc.

View full text Add to dashboard Cite

show abstract

“…The joining technology is an effective way to realize complex-shaped or large SiC ceramic parts. A wide range of methods have been reported to join SiC ceramics, such as metallic braze-based joining [5], the use of MAX phases [6], diffusion joining [7], polymerderived SiC joining [8], glass-ceramic joining joint [9], and Si-C reaction joining [10][11][12][13][14][15][16][17][18]. Among these methods, Si-C reaction joining is an attractive technique because the thermomechanical properties of the joint interlayer can be tailored to match those of the joining materials [16].…”

Section: Introductionmentioning

confidence: 99%

Joining of SiC Ceramic by Si–C Reaction Bonding Using Organic Resin as Carbon Precursor

Huang

Zhu

et al. 2022

Materials

View full text Add to dashboard Cite

In this study, the joining of silicon carbide (SiC) ceramics was achieved via a Si–C reaction bonding method using the phenolic resin (PF)–MgCl2 system as the carbon precursor. Specifically, by adding MgCl2 to the phenolic resin mixture, the average pore size of the product of carbonization of the PF resin mixture increased from 14 ± 5 nm to 524 ± 21 nm, which was beneficial for the infiltration of molten silicon at high temperature. The microstructure of the joined specimens and the effect of the inert filler on the joint strength were investigated. It was demonstrated that SiC–SiC joints with strong interfacial bonding and high flexural strength could be obtained by the Si–C reaction bonding method using a phenol formaldehyde resin/alcohol sol-gel system as the carbon precursor. The flexural strength of the joined specimens reached the highest value, i.e., 308 ± 27 MPa when the solid loading of the inert filler was 26%. Overall, stable joining of silicon carbide ceramics was achieved by the proposed method, which has significance for realizing the preparation of complex-shaped or large silicon carbide ceramic parts.

show abstract

Properties of TiB2–PSO modified SiHfBCN-based adhesive through polymer-derived-ceramic route

Luan

Dong²,

Li³

et al. 2022

Ceramics International

View full text Add to dashboard Cite

Wetting and joining of surface-oxidized SiC ceramic with calcium lithium aluminosilicate glass filler

Cited by 13 publications

References 45 publications

Joining SiC ceramics with ZrSi₂–SiC filler at low temperatures

Joining SiC ceramics with ZrSi₂–SiC filler at low temperatures

Joining of SiC Ceramic by Si–C Reaction Bonding Using Organic Resin as Carbon Precursor

Properties of TiB2–PSO modified SiHfBCN-based adhesive through polymer-derived-ceramic route

Contact Info

Product

Resources

About

Wetting and joining of surface-oxidized SiC ceramic with calcium lithium aluminosilicate glass filler

Cited by 13 publications

References 45 publications

Joining SiC ceramics with ZrSi2–SiC filler at low temperatures

Joining SiC ceramics with ZrSi2–SiC filler at low temperatures

Joining of SiC Ceramic by Si–C Reaction Bonding Using Organic Resin as Carbon Precursor

Properties of TiB2–PSO modified SiHfBCN-based adhesive through polymer-derived-ceramic route

Contact Info

Product

Resources

About

Joining SiC ceramics with ZrSi₂–SiC filler at low temperatures

Joining SiC ceramics with ZrSi₂–SiC filler at low temperatures