The role of friction film in friction, wear and noise of automotive brakes

Rhee, Seong Kwan; Jacko, M. G.; Tsang, P.H.S.

doi:10.1016/0043-1648(91)90226-k

Cited by 107 publications

(36 citation statements)

References 6 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Commercial friction materials are complex composites and may contain from 5 to 20 different ingredients [9]. These ingredients can be grouped into at least four classes, namely (i) fibrous reinforcement, (ii) binder, (iii) filler and (iv) friction modifier [10].…”

Section: Materials Ingredientsmentioning

confidence: 99%

Physical and chemical characteristics of commercially available brake shoe lining materials: a comparative study

Morshed

Haseeb

2004

Journal of Materials Processing Technology

View full text Add to dashboard Cite

Section: Materials Ingredientsmentioning

confidence: 99%

Physical and chemical characteristics of commercially available brake shoe lining materials: a comparative study

Morshed

Haseeb

2004

Journal of Materials Processing Technology

View full text Add to dashboard Cite

“…fibers, abrasives, binders, fillers, and friction modifiers (solid lubricants) into phenolic resin-based friction composites for the purpose of increasing the stability and wear resistance [1][2][3][4]. And naturally, the mechanical and tribological properties of the phenolic resin-based friction composites are greatly dependent on the interactions and synergetic effects among the multiphase ingredients.…”

Section: Introductionmentioning

confidence: 99%

Mechanical and tribological properties of phenolic resin-based friction composites filled with several inorganic fillers

Yan

2007

Wear

101

View full text Add to dashboard Cite

“…These results are consistent with the earlier works. [32][33][34][35] As can be seen from Table 3, the friction coefficients achieved for samples UCH-20 and UCH-16 are approximately 0.45, which is considered to be very good when compared to the coefficients of friction achieved with the current brake pads. The UC-4 sample has the highest density and hardness among the untreated samples.…”

Section: Wear Behaviourmentioning

confidence: 71%

Friction and wear behaviour of ulexite and cashew in automotive brake pads

Sugözü¹,

Mutlu²,

Keskin³

2015

Mater. Tehnol.

View full text Add to dashboard Cite

In the experimental studies, ulexite and cashew were investigated as new materials in brake pads. A newly formulated brake-pad material with five different ingredients was produced using ulexite. Tribological properties of the friction materials were obtained using the brake-test equipment. The friction and wear characteristics of the samples in contact with a disk made of cast iron were studied. The change in the friction coefficient, the temperature of the friction surface and the amount of the wear were examined to assess the performance of these samples. In addition, microstructural characterizations of the braking pads were carried out using scanning electron microscopy (SEM). The results showed that the friction materials containing ulexite and cashew have an important effect on the friction stability and fade resistance. The strategy proposed in this paper can be considered for the alternative friction materials where ulexite and cashew can be used as friction materials in the brake pads. Keywords: brake pad, composite materials, friction coefficient, ulexite, cashew Preiskovan je bil vpliv uleksita in prahu iz indijskega oreha kot novega materiala v zavornih oblogah. Novo zasnovani material za zavorne obloge iz petih sestavin je bil izdelan z uporabo uleksita. Tribolo{ke lastnosti tornega materiala so bile preizku{ene na napravi za preizkus zavor. Preu~evano je bilo trenje in zna~ilnosti obrabe vzorcev v stiku z diskom iz sive litine. Za oceno zmogljivosti vzorcev so bile preiskane spremembe koeficienta trenja, izmerjena temperatura na povr{ini stika in koli~ina obrabe. Z vrsti~nim elektronskim mikroskopom (SEM) so bile dodatno preiskane mikrostrukturne zna~ilnosti zavornih oblog. Rezultati so pokazali, da imajo torni materiali, ki vsebujejo uleksit in prah indijskega oreha, pomemben vpliv na stabilnost trenja in odpornost proti odpovedi zavor pri vi{jih temperaturah. V tem~lanku predlagana usmeritev se lahko upo{teva kot nadomestni torni material za zavorne obloge na osnovi uleksita in prahu iz indijskega oreha. Klju~ne besede: zavorne obloge, kompozitni material, koeficient trenja, uleksit, prah iz indijskega oreha

show abstract

The role of friction film in friction, wear and noise of automotive brakes

Cited by 107 publications

References 6 publications

Physical and chemical characteristics of commercially available brake shoe lining materials: a comparative study

Physical and chemical characteristics of commercially available brake shoe lining materials: a comparative study

Mechanical and tribological properties of phenolic resin-based friction composites filled with several inorganic fillers

Friction and wear behaviour of ulexite and cashew in automotive brake pads

Contact Info

Product

Resources

About