Synthesis of high-performance alkyd anticorrosion coatings based on waste poly(ethylene terephthalate)

Popović, Ivanka G.; Rusmirovic, D Jelena; Rančić, Milica; Tasić, Ana; Lazić, Dragana; Marinković, Dragan

doi:10.5937/zasmat1504483p

Cited by 4 publications

(9 citation statements)

References 8 publications

(8 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Open Sci. 8: 202375 [22,28]. Even if the films encounter physical damage in daily life, the films will not leave the surface of the substrate.…”

Section: Physical Properties Of the Water-reducible Alkyd Resin Filmsmentioning

confidence: 99%

“…For example, alkyd resins based on the glycolysis products of waste PET had been synthesized and corresponding alkyd-amino baking paint had also been explored by Torlakog˘lu and Güçlü [21]. Besides, high-performance alkyd resins had been prepared from glycolysis products of different polyols [22]. Moreover, alkyd resins had also been prepared with hyperbranched polyester and glycolysis products of waste PET, and the effects of the fatty acid types, glycolysis products and polyol functionality on thermal properties and film properties had been studied [23].…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Preparation of autoxidative water-reducible alkyd resins from waste polyethylene terephthalate

et al. 2021

View full text Add to dashboard Cite

In this paper, the waste polyethylene terephthalate (PET) was glycolysed by trimethylolpropane with zinc acetate as catalyst. The effects of different content glycolysis product of waste PET on the appearance, viscosity, particle size and molecular weight of autoxidative water-reducible alkyd resins and the corresponding film adhesion, flexibility, impact resistance, gloss, hardness and chemical resistance were studied. Meanwhile, experimental results were compared with commercial water-reducible alkyd and water-reducible alkyd without the glycolysis product of waste PET. The results show that the maximum concentration of PET in autoxidative water-reducible alkyd resins can reach 8.5 wt%, and the molecular weight, particle size and viscosity of water-reducible alkyd resin do not change much with the increase of PET concentration. The introduction of PET resulted in the viscosity of water-reducible alkyd resins being greater than that of water-reducible alkyd resin without PET; this is mainly because PET contains harder terephthalic acid monomer units. However, the particle size of water-reducible alkyd resins with waste PET is significantly lower than that of the water-reducible alkyd resin without PET; this is due to PET-free water-reducible alkyd resin containing more pentaerythritol with greater steric hindrance. In addition, the hardness of the water-reducible alkyd resin paint film (PET content is 8.5%) reaches 1H, which is higher than the hardness (HB) of the water-reducible alkyd resin paint film without PET and the commercial alkyd resin paint film, while the physical properties and chemical resistance of the former are comparable to those of the latter two kinds of paint films. Therefore, the use of waste PET in water-borne coatings systems not only reduces the cost of coatings, but also opens up a new market for recycled PET, which may contribute a promising method for management of waste PET.

show abstract

“…Open Sci. 8: 202375 [22,28]. Even if the films encounter physical damage in daily life, the films will not leave the surface of the substrate.…”

Section: Physical Properties Of the Water-reducible Alkyd Resin Filmsmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Preparation of autoxidative water-reducible alkyd resins from waste polyethylene terephthalate

et al. 2021

View full text Add to dashboard Cite

show abstract

“…Procedure for the isolation of fatty acids from linseed oil (LFA) has been performed analogously to the following publication [16]. In the ethanol solution of linseed oil (LO), KOH was added slowly, so that obtained molar ratio KOH/LO was 3.5/1.…”

Section: Isolation Of Unsaturated Fatty Acid From Linseed Oilmentioning

confidence: 99%

Modified tannins for alkyd based anticorrosive coatings

Milošević¹,

Daničić²,

Kovačina³

et al. 2019

Zaštita materijala

View full text Add to dashboard Cite

The study of the synthesis of anticorrosive inhibitors, based on chemically modified tannins, and their use in alkyd based coatings to improve anticorrosive properties is presented in this work. Two methods of tannin modification were applied: direct method using ammonium hydroxide, ammonium hydroxide/ammonium chloride buffer or diethylenetriamine (DETA); and a two-step method including tannin modification with epichlorohydrin (ECH) in first step to produce epoxy modified tannin, ET, and further modification with heteroaromatic amines or linseed oil fatty acids (LFA) in second step. The obtained anticorrosive additives were characterized using ATR-FTIR, 1 H and 13 C NMR spectroscopies and elemental analysis. Epoxy, amino, hydroxyl, acid and iodine values of the synthesized inhibitors were determined according to standard methods. The prepared alkyd coating with tannin inhibitors was tested according to standard SRPS EN ISO 4628 method. Anticorrosive coating containing modified tannin based additive showed increased anticorrosive properties, good adhesion and coverage comparing to the coating with zinc phosphate additive. The alkyd coating films based on ET-LFA and ET modified with 2-amino-5mercapto-1,3,4-thiadiazole showed best anticorrosive results.

show abstract

“…Glycolysis of PET using TMP and TME was performed according to the procedure described in literature earlier [6,16]. Molar ratio of PET and multifunctional alcohol was 1:3 and TBT was used as catalyst.…”

Section: Glycolysis Of Petmentioning

confidence: 99%

“…The top layer of linseed oil fatty acids (LFA) was separated and refined twice with 250 ml of diethyl ether and vacuum distillated which enabled drying and removal of low boiling component of reaction product. Characteristics of LFA: AV=210 mg KOH/g; JV=157 g/100 g [16].…”

Section: Isolation Of Fatty Acid Of Linseed Oil (Fla)mentioning

confidence: 99%

Alkyd nanocomposite coatings based on waste pet glicolyzates and modified silica nanoparticles

Rušmirović¹,

Božić²,

Stamenović³

et al. 2016

Zas Mat

Self Cite

View full text Add to dashboard Cite

show abstract

Synthesis of high-performance alkyd anticorrosion coatings based on waste poly(ethylene terephthalate)

Cited by 4 publications

References 8 publications

Preparation of autoxidative water-reducible alkyd resins from waste polyethylene terephthalate

Preparation of autoxidative water-reducible alkyd resins from waste polyethylene terephthalate

Modified tannins for alkyd based anticorrosive coatings

Alkyd nanocomposite coatings based on waste pet glicolyzates and modified silica nanoparticles

Contact Info

Product

Resources

About