Synthesis of Alfa (Stipa tenacissima L.)/Hemp Fiber-Reinforced UHMWPE: Impact of Fibers on Mechanical, Microstructural and Aspect Properties

Vinod, B.; Suresh, S.; Reddy, S. Sunil Kumar; Sudhakara, D.; Elaiyarasan, U. Uthirapathi

doi:10.1007/s40033-022-00357-7

Cited by 4 publications

(1 citation statement)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In recent studies, the procurement of SPS equipment and materials fabrication increased rapidly due to producing complex shapes. As a cutting-edge material processing technique, spark plasma sintering (SPS) creates uniformity in the distribution of the materials and helps functionally gradient materials, structural components, and wear-resistant thermoelectric semiconductors [11]. It is sustained by pulsating direct current (impulse frequency varies from one ms to one second, with a current amplitude of 0.01 to 10kA), which is used in a variety of devices, from the outset to the end.…”

Section: Fabrication Of Magnesium Hybrid Compositesmentioning

confidence: 99%

Tribological and Mechanical Characteristics of Mg–Zn6.0–Y1.2–Zr0.2 alloy by SPS Technique: Natural and Agro-Waste Utilization

Vinod

Suresh²,

Reddy³

et al. 2022

J Bio Tribo Corros

Self Cite

View full text Add to dashboard Cite

In India, urban solid waste generation has risen over the last decade. The aspect of waste generation is a large amount of waste materials among all solid waste types. While using ash particles eliminates waste, it also contributes desirable qualities. In this research work, the effects of Himalayan nettle leaf ash (HNLA) bean pod ash (BPA) with molybdenum trioxide (MoO3) on the ZWK611 (Mg-Zn6.0-Y1.2-Zr0.2) alloy is examined. The as-cast alloy exhibits an α-Mg matrix, and cubic γ-phases are formed in addition to MoO3 particles. In this work, an attempt was made to choose a ZWK611 alloy reinforced with HNLA and BPA by varying weight percentages (X = 4, 8, 12, and 15%) with a constant weight percentage of MoO3 (5%) fabricated using spark plasma sintering (SPS) technique. The mechanical and physical properties were tested for both as-cast alloy and magnesium hybrid composites. Surface morphology and XRD are analysed to identify material behaviour. The addition of 12%(HNLA-BPA)/5%(MoO3) hybrid composite exhibits high strength as compared to the as-cast alloy.

show abstract

Section: Fabrication Of Magnesium Hybrid Compositesmentioning

confidence: 99%

Tribological and Mechanical Characteristics of Mg–Zn6.0–Y1.2–Zr0.2 alloy by SPS Technique: Natural and Agro-Waste Utilization

Vinod

Suresh²,

Reddy³

et al. 2022

J Bio Tribo Corros

Self Cite

View full text Add to dashboard Cite

show abstract

Valorization of the use of natural Alfa (Stipa tenacissima L.) fiber in composite reinforcing plates based on natural fibers and metal fabric

Helaili

Guizani

Chafra

2023

Innov. Infrastruct. Solut.

View full text Add to dashboard Cite

The morphological and mechanical characterization of UHMWPE based composite: an experimental study

Basrani¹,

Kumar²,

Kumar³

2023

Phys. Scr.

View full text Add to dashboard Cite

Natural fiber and its hybrid composites have a promising future due to their economic, lightweight, environmentally superior, and sustainable properties. The purpose of this research is to explore the morphological and physical properties of composites made of hemp-epoxy and ultra-high molecular weight polyethylene-hemp-epoxy. The compression moulding technique is used to fabricate the UHMWPE -hemp hybrid composite and hemp-epoxy sample at a different orientation. These samples are subjected to different types of mechanical testing, including flexural, impact, hardness, and tensile tests at different strain rates as per ASTM standards. The result indicates that the flexural strength, impact strength, and hardness of the hybrid composite are more than the hemp composite. Scanning electron microscopy has been used to examine fractography at various strain rates. It is found that with the increase in the strain rate, tensile strength increases. It is observed that there is an increase of more than 56.49% in the specimen’s strength with the addition of 8.3% ultrahigh molecular weight polyethene fiber reinforcement.

show abstract

Synthesis of Alfa (Stipa tenacissima L.)/Hemp Fiber-Reinforced UHMWPE: Impact of Fibers on Mechanical, Microstructural and Aspect Properties

Cited by 4 publications

References 21 publications

Tribological and Mechanical Characteristics of Mg–Zn6.0–Y1.2–Zr0.2 alloy by SPS Technique: Natural and Agro-Waste Utilization

Tribological and Mechanical Characteristics of Mg–Zn6.0–Y1.2–Zr0.2 alloy by SPS Technique: Natural and Agro-Waste Utilization

Valorization of the use of natural Alfa (Stipa tenacissima L.) fiber in composite reinforcing plates based on natural fibers and metal fabric

The morphological and mechanical characterization of UHMWPE based composite: an experimental study

Contact Info

Product

Resources

About