Switched capacitor‐based continuous input current high step‐up impedance source DC–DC converter

To overcome the problems associated with Z-source-based DC-DC converters, a quasi-Z-source (QZS)-based high-gain DC-DC boost converter with switched capacitors is proposed in this work. Z-source-based DC-DC converters have problems like low-voltage gain, discontinuous input current, and high-voltage stress on the active and passive components. The proposed converter can produce a high-voltage gain of more than 10 times for a duty cycle of less than 0.5. The converter has other desirable features like reduced voltage stress across the switching components and continuous input current (CIC). It comprises a QZS cell made up of switched inductors and a voltage multiplier cell (VMC) made up of switched capacitors. The power loss analysis is done using PLECS software by incorporating the real parameters of switches and diodes from the datasheet. A hardware prototype of 200 W is developed in the laboratory to verify the working of the converter. In experimental results for an output power of 200 W, the converter is operated with a source voltage of 33 V at a duty ratio of 0.4 providing an output voltage of 395 V. The converter performance is good in open-loop conditions and is verified through experimental results. K E Y W O R D S duty ratio (λ), quasi-Z-source (QZS), voltage multiplier cell (VMC), voltage stress | INTRODUCTIONNowadays, gain DC-DC converters have found applications in electric vehicles (EVs), DC microgrids, switch-mode power supplies, and robotics to name a few. The power range of these high-gain converters varies from few milliwatts to a kilowatt range. The main objective is to build a topology with a high gain and reduced number of components. Desirable features like low voltage and current stress, common ground with low ripple in input current make the highgain converter an attractive choice for renewable energy applications. Conventional step-up converters and their variants need to be operated at a high duty ratio (λ) to obtain high-voltage gain. Consequently, the efficiency decreases, and the stress across the components increases. Moreover, the low and fluctuating output voltage of the PV panel cannot be fed to the inverter directly; it must be boosted with reduced ripple using a high-gain converter. 1,2 In Figure 1, it is depicted that a high-gain DC-DC converter can effectively boost the voltage from various sources like fuel cells, solar PV modules, battery, and an ultra-capacitor. These converters are used at the front end of a grid-connected inverter to maintain the DC-link voltage. The DC-DC converters have isolated and non-isolated structures. The isolated structures

Section: Introductionmentioning

confidence: 99%

mentioning

confidence: 99%

A non‐isolated quasi‐Z‐source‐based high‐gain DC–DC converter

Mahmood

Zaid

Khan

et al. 2021

“…To achieve higher efficiency, adjacent inductor topologies using active or passive clamp structures are used. This technique gives a soft‐switching condition to the power switch 31–42 …”

Section: Introductionmentioning

confidence: 99%

“…In Ahmad et al, 33 SC‐based quasi‐Z‐source converter (qZSC) topology for DC microgrids is introduced. Abbasi et al 34 have proposed a new nonisolated step‐up/down and step‐up SC‐based DC–DC converter topology.…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

A design for switched capacitor and single‐switch DC–DC boost converter by a small signal‐based PI controller

Ertekin

Bulut

Tekin

et al. 2022

In this study, a switched capacitor (SC)‐based single‐switch DC–DC boost converter structure operating under the high voltage gain and the low duty ratio is proposed using the PI control technique. High current and voltage stresses across the power switches and power diodes can be reduced by using the projected SC block. In addition, the proposed converter can achieve high voltage gain through shorter duty cycles, which directly reduces the voltage stress and dynamic losses in the power semiconductors. On the other hand, because the proposed converter includes a single power switch under different output powers and different loads, the control process is simpler than multiswitch structures. With the proposed converter, an output voltage of 10 times greater rather than the input voltage is obtained at 0.57 of the duty cycle. In this study, the fundamental functions of the proposed converter and the controller design steps are analyzed mathematically and tested in MATLAB/SIMULINK environment. As a result of the analysis, it was determined that the proposed topology works with a high performance at high frequency and variable load ranges. To validate the proposed converter and theoretical calculations, a 200‐W prototype was established under a continuous conduction mode (CCM) working state, with 48‐VDC input voltage and 400‐VDC output voltage. Finally, the simulation results were tested and verified through the experimental results.

An efficient DC‐DC converter for inductive power transfer in low‐power sensor applications

Hossain

Alexander

et al. 2022

Summary Inductive power transfer has become an emerging technology for its significant benefits in many applications, including mobile phones, laptops, electric vehicles, implanted bio‐sensors, and internet of things (IoT) devices. In modern applications, a direct current–direct current (DC–DC) converter is one of the essential components to regulate the output supply voltage for achieving the desired characteristics, that is, steady voltage with lower peak ripples. This paper presents a switched‐capacitor (SC) DC–DC converter using complementary architecture to provide a regulated DC voltage with an increased dynamic response. The proposed topology enhances the converter efficiency by decreasing the equivalent output resistance to half by connecting two symmetric SC single ladder converters. The proposed converter is designed using the standard 130‐nm BiCMOS process. The results show that the proposed architecture produces 327‐mV DC output with a rise time of 60.1 ns and consumes 3.449‐nW power for 1.0‐V DC supply. The output settling time is 43.6% lower than the single‐stage SC DC–DC converter with an input frequency of 200 MHz. The comparison results show that the proposed converter has a higher power conversion efficiency of 93.87% and a lower power density of 0.57 mW/mm2 compared to the existing works.