Superiority of Artificial Neural Networks Over Statistical Methods in Prediction of the Optimal Length of Rock Bolts

Abstract

Rock bolting is one of the most important support systems used for rock structures. Rock bolts are widely used in underground excavations as they are suitable for a wide range of geological conditions and allow using progressive design methods; besides, they help economising in the use of materials and manpower. Thus, to provide the most effective support at minimum cost by means of rock bolting, it is essential to optimise the elements contributing to bolt design, including their length, as well as bolt density and tension during installation. This paper considers the length of bolts for optimisation of the design phase, which is one of the most important parameters impacting the entire design procedure. Presenting and comparing results of some statistical models, neural network modeling is introduced as powerful means in prediction of the optimal length of rock bolts. Subsequent to training and testing of a large number of 1-layer and 2-layer backpropagation neural networks, it was reported that the optimal model was the network with the architecture of 6-18-3-1 as it demonstrated the minimum RMSE and MAE as well as the maximum R 2 . In comparison to statistical models (0.7182 for the value of R 2 in the multiple linear regression model, 0.68 in the polynomial model and 0.7 in the dimensionless model), the results obtained by the neural network modeling − i.e. the coefficient of determination R 2 of 0.9259, the value of mean absolute error MAE of 0.068, and the root mean squared error RMSE of 0.078 − not only proved their superiority but also introduced the neural network modelling as a highly capable prediction tool in forecasting the optimal length of rock bolts. Furthermore, sensitivity analysis was used to obtain parameters that have the greatest and the least impact on the optimal bolt length: the effect of the overburden thickness, tensile strength, cohesion and Poisson's ratio on the optimal bolt length was almost the same while the friction angle had the least influence.Keywords: optimal length of rock bolts, artificial neural networks, statistical methods, sensitivity analysis.

Evaluation of Induced Settlements of Piled Rafts in the Coupled Static-Dynamic Loads Using Neural Networks and Evolutionary Polynomial Regression

“…In order to make all the input and output parameters dimensionless, (7) [28,29] is used and all the parameters are normalized to a 0-1 scale.…”

“…Hence, the application of neural network modeling and evolutionary polynomial regressions (EPRs), which are believed to be common ways to accurately and timely predict engineering complicated functions, can be examined. Different attempts to apply neural networks and EPRs to model different civil and geotechnical problems are presented in the literature [14][15][16][17][18][19][20][21][22][23][24][25][26][27][28][29][30][31][32][33]. They are well-applied in a wide range of problems from deep soil stabilizations, concrete, and their related structures, compressive strength of soils, rocks, and stabilized samples, bearing capacity of shallow and deep foundations, lateral spreading, rock mechanics, rock engineering, and soil mechanics [14][15][16][17][18][19][20][21][22][23][24][25][26][27][28][29][30][31][32][33].…”

Neural Prediction of Tunnels’ Support Pressure in Elasto-Plastic, Strain-Softening Rock Mass

“…ANNs are broadly applied in engineering [22][23][24][25][26][27][28][29]. Also, over the last decades, ANNs have appeared as efficient meta-modelling methods applicable to a wide range of sciences, including material science and structural engineering [30][31][32].…”

“…It was conducted on the basis of the commonly known coefficient of determination (R 2 ), root-mean-square error (RMSE), and mean absolute error (MAE) [22,24,27,28,[40][41][42][43][44][45][46][47].…”

ANN modeling of pull-off adhesion of concrete layers

“…In order to correlate the parameters it was proposed to use artificial neural networks (ANN). The latter have been increasingly used in construction [12][13][14][15][16][17][18][19][20][21].…”