Study on stability, fuel properties, engine combustion, performance and emission characteristics of biofuel emulsion

Reham, S. S.; Masjuki, H.H.; Kalam, M.A.; Shancita, I.; Fattah, I.M. Rizwanul; Ruhul, A. M.

doi:10.1016/j.rser.2015.08.013

Cited by 90 publications

(28 citation statements)

References 84 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Reham et al [40] studied that with a method of injection in a common rail diesel engine fueled with ultra low sulfur diesel (ULSD) and biodiesel. They reported that higher biodiesel blending rates required higher injection pressure because of the high surface tension of biodiesel.…”

Section: Introductionmentioning

confidence: 99%

Application of Canola Oil Biodiesel/Diesel Blends in a Common Rail Diesel Engine

Yoon²,

Kim

et al. 2016

Applied Sciences

View full text Add to dashboard Cite

Abstract:In this study, the application effects of canola oil biodiesel/diesel blends in a common rail diesel engine was experimentally investigated. The test fuels were denoted as ULSD (ultra low sulfur diesel), BD20 (20% canola oil blended with 80% ULSD by volume), and PCO (pure canola oil), respectively. These three fuels were tested under an engine speed of 1500 rpm with various brake mean effective pressures (BMEPs). The results indicated that PCO can be used well in the diesel engine without engine modification, and that BD20 can be used as a good alternative fuel to reduce the exhaust pollution. In addition, at low engine loads (0.13 MPa and 0.26 MPa), the combustion pressure of PCO is the smallest, compared with BD20 and ULSD, because the lower calorific value of PCO is lower than that of ULSD. However, at high engine loads (0.39 MPa and 0.52 MPa), the rate of heat release (ROHR) of BD20 is the highest because the canola oil biodiesel is an oxygenated fuel that promotes combustion, shortening the ignition delay period. For exhaust emissions, by using canola oil biodiesel, the particulate matter (PM) and carbon monoxide (CO) emissions were considerably reduced with increased BMEP. The nitrogen oxide (NOx) emissions increased only slightly due to the inherent presence of oxygen in biodiesel.

show abstract

Section: Introductionmentioning

confidence: 99%

Application of Canola Oil Biodiesel/Diesel Blends in a Common Rail Diesel Engine

Yoon²,

Kim

et al. 2016

Applied Sciences

View full text Add to dashboard Cite

show abstract

“…This is because the water contents in biofuels are very high. The water content is vaporized during the combustion, taking up the heat produced from the combustion and lowering the heating value of fuel [6]. Since the heating values of the blends are decreased as the biofuels increased in blends, the brake thermal efficiency of the engine can be predicted to increase …”

Section: Resultsmentioning

confidence: 99%

“…Besides, it is capable of reducing the harmful exhaust emission such as CO, CO2, SOx, smoke opacity and particulate matter [5]. However, ethanol is not miscible in diesel fuel due to their physical properties difference and ethanol contains high oxygen content that leads to high NOx emission [6] [7] and knocks problem. Besides, ethanol has extremely low cetane number [8] that increase the ignition time delay which leads to knock problem.…”

Section: Introductionmentioning

confidence: 99%

Investigation of diesel-ethanol blended fuel properties with palm methyl ester as co-solvent and blends enhancer

et al. 2016

View full text Add to dashboard Cite

Abstract. Diesel engine is known as the most efficient engine with high efficiency and power but always reported as high fuel emission. Malaysia National Automotive Policy (NAP) was targeting to improve competitive regional focusing on green technology development in reducing the emission of the engine. Therefore, ethanol was introduced to reduce the emission of the engine and while increasing its performance, Palm methyl ester was introduced as blend enhancer to improve engine performance and improve diesel-ethanol blends stability. This paper aimed to study the characteristics of the blends and to prove the ability of palm-methyl-ester as co-solvent in ethanol-diesel blends. Stability and thermophysical test were carried out for different fuel compositions. The stability of dieselethanol blended was proved to be improved with the addition of PME at the longer period and the stability of the blends changed depending on temperature and ethanol content. Density and viscosity of diesel-ethanol-PME blends also give higher result than diesel-ethanol blends and it's proved that PME is able to increase density and viscosity of blends. Besides, heating value of the blends also increases with the increasing PME in diesel-ethanol blends.

show abstract

“…The emulsification of biodiesel (BD) and petrodiesel (PD) with water and other materials has long been researched [1], [2], [3], [4] for combustion related purposes. Previous research has explored single droplet combustion characteristics for BD and PD [5] and their water emulsions [6].…”

Section: Introductionmentioning

confidence: 99%

Experimental Investigation of Water Emulsion Fuel Stability

Singh

Lopes

Hentges

et al. 2019

Volume 7: Fluids Engineering

View full text Add to dashboard Cite

The combustion of liquid fuels emulsified with water have long generated interest in the internal combustion engine research community. Typically, these fuels consist of small quantities of water emulsified with ultrasonification or other mechanical methods into a pure or multicomponent hydrocarbon fuel. These emulsion fuels promise significant advantages over base liquid fuels, such as better fuel economy, colder combustion temperatures, less NOx emissions, and so on. However, a significant practical disadvantage of these fuels is that they are prone to phase separation after they have been prepared. Till date, an objective but economical method of identifying the various degrees of phase separation has not been identified. Present research presents such a method and shows its utilization in analyzing the stability of water and hydrocarbon fuel emulsions over time without the addition of chemical stabilizers. It is expected that present research will pave the way in establishing this method to study the stability of other specialized multicomponent fluids.

show abstract

Study on stability, fuel properties, engine combustion, performance and emission characteristics of biofuel emulsion

Cited by 90 publications

References 84 publications

Application of Canola Oil Biodiesel/Diesel Blends in a Common Rail Diesel Engine

Application of Canola Oil Biodiesel/Diesel Blends in a Common Rail Diesel Engine

Investigation of diesel-ethanol blended fuel properties with palm methyl ester as co-solvent and blends enhancer

Experimental Investigation of Water Emulsion Fuel Stability

Contact Info

Product

Resources

About