Stability improvement of large-scale power systems in the presence of wind farms by employing HVDC and STATCOM based on a non-linear controller

Jalilvand, Abolfazl; Ashouri, Ahmad; Bagheri, Amir

doi:10.1016/j.ijepes.2020.106021

Cited by 13 publications

(9 citation statements)

References 29 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The STATCOM model presented in this section is based on the principle of convenience [26]. Figure 2 shows the STATCOM simplified design circuit, which illustrates that this device is a sinusoidal voltage source coupled to a network node via the coupling transformer inductance.…”

Section: Modeling Of Statcommentioning

confidence: 99%

“…A series resistor is also included in the circuit to simulate the transformer power losses as well as the losses in the inverter switches. The global model of the static synchronous compensator is described by (1), using the reference frame in [26]. The mathematical model of the STATCOM after park transformation (d q) frame is obtained as (2).…”

Section: Modeling Of Statcommentioning

confidence: 99%

See 1 more Smart Citation

Impact of static synchronous compensator STATCOM installation in power quality improvement

Moufid

En-nay

Naciri

et al. 2022

IJPEDS

View full text Add to dashboard Cite

<span lang="EN-US">The present work investigates the flexible AC transmission system (FACTS) device's role to improve the voltage stability for a distribution network of various types of loads. Our analysis was based on using a static synchronous compensator (STATCOM) device over a test distribution system. Firstly, a detailed description of the mathematical model used in our system is presented. Then we studied the effect of inductive and capacitive loads with and without STATCOM. To investigate the efficacy and robustness of using STATCOM in a distribution network, a test system is developed using MATLAB/Simulink, where we analyzed the voltage profile in different cases. The results of the simulation demonstrate that the STATCOM plays a critical role in optimizing the voltage profiles of distribution systems, either capacitive or inductive.</span>

show abstract

Section: Modeling Of Statcommentioning

confidence: 99%

Section: Modeling Of Statcommentioning

confidence: 99%

Impact of static synchronous compensator STATCOM installation in power quality improvement

Moufid

En-nay

Naciri

et al. 2022

IJPEDS

View full text Add to dashboard Cite

show abstract

“…In addition to this, DSTATCOM is also used to maintain the load voltage at 1p.u during voltage swells/sags. Shunt active power filters are used in each phase to improve the PCC voltage, which makes the system more difficult to control [22]. The system performance is virtual for load step changes and voltage sag conditions.…”

Section: Model Predictive Controlmentioning

confidence: 99%

A Review of Different Configurations and Control Techniques for DSTATCOM in the Distribution system

2021

View full text Add to dashboard Cite

This paper presents a review of DSTATCOM Topologies and power quality control Techniques. The used topologies are Three-phase Three-wire and Three-phase four-wire and control techniques are Instantaneous reactive power theory(IRP), Synchronous Reference Frame Theory(SRF), Model Predictive Control (MPC), Sliding mode control(SMC), Adaptive Neuro-fuzzy interface systems(ANFIS) and Artificial intelligence based controllers. These control techniques are used to mitigate the reactive power compensation, load balancing, Neutral current compensation, harmonics reduction and maintains the Total harmonic Distortion in IEEE519 standards. Performance investigated in Single-phase Distribution systems by connecting with STATCOM and without DSTATCOM in MATLAB/SIMULINK

show abstract

“…The modeling of the STATCOM, though well known, is reviewed in the lines below, for the sake of convenience [21,22]. The Figure 2 represented the simplified model circuit of the STATCOM, so this device is a sinusoidal voltage source connected to a network node by the inductance of the coupling transformer.…”

Section: Modeling Of Statcommentioning

confidence: 99%

Real-time simulation of static synchronous condenser (STATCOM) for compensation of reactive power

Hinda

Khiat

2020

IJECE

View full text Add to dashboard Cite

This paper presents a real time simulation stability of power system by static synchronous condenser (STATCOM) in modern platform real-time simulator named (RT-LAB) using the latest INTEL quad-core processors to simulate a relatively large power system In our work, We have to study the problem of controlling voltage and reactive power in electric system by static synchronous condenser (STATCOM). All the simulations for the above work have been carried out using MATLAB /Simulink and RT-LAB Various simulations have given very satisfactory results and we have successfully improved the voltage by injecting a FACTS device, which is the STATCOM, the Studies and Comparisons of real-time simulation results of the power system with and without STATCOM connected illustrate the effectiveness and capability of STATCOM in improving voltage stability in power system.

show abstract

Stability improvement of large-scale power systems in the presence of wind farms by employing HVDC and STATCOM based on a non-linear controller

Cited by 13 publications

References 29 publications

Impact of static synchronous compensator STATCOM installation in power quality improvement

Impact of static synchronous compensator STATCOM installation in power quality improvement

A Review of Different Configurations and Control Techniques for DSTATCOM in the Distribution system

Real-time simulation of static synchronous condenser (STATCOM) for compensation of reactive power

Contact Info

Product

Resources

About