Regularities of Obtaining Metal-Filled Polymer Composites

Kucherenko, Anastasiia; Moravskyi, Volodymyr; Kuznetsova, M.Ya.; Grytsenko, Oleksandr; Masyuk, Andrii; Dulebová, Ľudmila

doi:10.1007/978-981-15-3996-1_6

Cited by 8 publications

(4 citation statements)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Obtaining metal-filled composite materials with high technological and operational properties requires the development of alternative technological solutions for their production. The technology of obtaining metal-filled polymer composites by the metallization of polymer raw materials with its subsequent processing by standard methods directly into products was used [33][34][35][36]. As a result, the process of combining the components is significantly facilitated and uniform distribution of the metal filler in the polymer matrix is ensured.…”

Section: Introductionmentioning

confidence: 99%

Utilization of Polypropylene in the Production of Metal-Filled Polymer Composites: Development and Characteristics

et al. 2020

View full text Add to dashboard Cite

Metal-filled composites based on polypropylene waste have been successfully obtained with an injection molding method of metalized polymer raw materials. Using the model polymer, the peculiarities of the formation of the copper layer in solutions of chemical metallization on the polypropylene surface were investigated and the main factors influencing this process were established. The main influence on the rate of reduction of copper in solutions of chemical metallization has the concentration of copper sulfate, sodium hydroxide, and EDTA-Na2. It was shown that the efficiency of the copper plating process also strongly depends on polymer processing, which follows the activation. In case of the use of simple activation, it is not possible to obtain metalized raw materials with high efficiency. Additional processing of activated polymer raw materials is required to carry out the process with high efficiency. The amount of reduced copper on the polymer surface can be adjusted by changing the concentration of the components of the chemical metallization solution, as well as the degree of loading of the polymer raw material. Examination by electron scanning microscopy of the obtained metalized polypropylene showed that the copper coating on the polymer particles is formed with a high degree of surface coverage. The formed copper coating is free of copper oxides, which is confirmed by X-ray diffraction studies and analysis of the spectrum of characteristic X-rays. Metal-filled composites have been characterized by the effect of copper on mechanical and rheological (MFR) properties. The Differential Scanning Calorimetry (DSC) and Thermogravimetric (TG) methods show a certain effect of metal on the magnitude of thermal effects and the rate of weight loss.

show abstract

Section: Introductionmentioning

confidence: 99%

Utilization of Polypropylene in the Production of Metal-Filled Polymer Composites: Development and Characteristics

et al. 2020

View full text Add to dashboard Cite

show abstract

“…The developed technique, which includes the activation of the surface of the granules and their subsequent metallization in chemical reducing solutions, was used to obtain metallized polyethylene granules (Liten PL-10 (Unipetrol, Litvínov, Czech Republic)) [ 53 , 54 , 55 , 56 , 57 ].…”

Section: Methodsmentioning

confidence: 99%

Obtainment and Characterization of Metal-Coated Polyethylene Granules as a Basis for the Development of Heat Storage Systems

et al. 2022

View full text Add to dashboard Cite

The research studied the feasibility of using copper-coated polyethylene granules as a basis for creating efficient heat storage systems. A technology for imparting catalytic properties to a polymer surface by the joint processing of polymer granules and an activator metal in a ball mill with their subsequent metallization in a chemical reducing solution is proposed. The efficiency of copper-coating a polyethylene surface is shown to be largely determined by the activation stage and the assumption regarding the mechanism of interaction of the activator metal with the polymer surface is made. To obtain different amounts of metal on the polyethylene granules, it is proposed that the method of remetallization is used. It was established that the rate of copper ion reduction depends on the number of previous coatings and is determined by the area of interaction of the metal-coated granules with the chemical reducing solution. The obtained metal-coated polyethylene granules were characterized in terms of the viability of using it as a phase transition material for a heat storage system. Using the developed installation that simulates the heat accumulator operation, it was shown that the efficiency of using metal-coated polyethylene granules to create heat storage systems is higher. The copper coating deposited on the polyethylene granules was studied using scanning electron microscopy and X-ray diffraction analysis.

show abstract

“…[1][2][3][4][5][6][7] Obtaining metal-filled polymer composites with a wide range of technological and operational properties, their combination and predictable regulation become possible due to a number of factors. First of all, it is the presence of polymer matrices different in nature and, accordingly, in their characteristics (thermosets, 8,9 thermoplastics, 3,10 elastomers, 11,12 hydrogels 13,14 ) and metal fillers (metals, 8,15 noble metals, 16,17 ferromagnets, 18,19 metal alloys, 20,21 bimetals, 22 and hybrids 23 ). The properties of the composite are significantly influenced by the choice of the modification method of the polymer matrix, which is determined by the method of obtaining metal-filler particles (chemical, physical, electrochemical) [24][25][26][27] and the method of introducing the filler into the polymer matrix (synthesis of metal-filler particles in the polymer network, 28 synthesis of metal-filler particles during the formation of the polymer matrix, 29 mixing in the melt 18,30 and solution, 11 polymerization of the monomer in the presence of the metal particles 8,14 ).…”

Section: Introductionmentioning

confidence: 99%

Thermophysical Properties of Composite Metal-Filled Copolymers of Polyvinylpyrrolidone

Grytsenko,

Bratychak Jr.,

Dulebova

et al. 2024

ChChT

View full text Add to dashboard Cite

The effect of the presence of finely dispersed metal fillers of various natures (Zn, Co, Ni) on the thermophysical characteristics (Vick heat resistance, glass transition temperature) of polyvinylpyrrolidone block copolymers with 2-hydroxyethylmethacrylate was studied. It was found that the heat resistance of the obtained composites significantly exceeds the heat resistance of unfilled copolymers and is in the range of 360-395K, depending on the nature and content of the metal filler. The change in heat resistance correlates with the change in glass transition temperature, which was evaluated according to the results of thermomechanical and dynamic mechanical thermal analyses. The results of this work are an additional source to characterize the structure of metal-filled copolymers: they confirm the participation of metal filler particles in the formation of the nodes of the copolymer spatial network, and also prove the formation of a different polymer network structure in the interfacial layer on the surface of the metal particle and in the polymer volume.

show abstract

Regularities of Obtaining Metal-Filled Polymer Composites

Cited by 8 publications

References 21 publications

Utilization of Polypropylene in the Production of Metal-Filled Polymer Composites: Development and Characteristics

Utilization of Polypropylene in the Production of Metal-Filled Polymer Composites: Development and Characteristics

Obtainment and Characterization of Metal-Coated Polyethylene Granules as a Basis for the Development of Heat Storage Systems

Thermophysical Properties of Composite Metal-Filled Copolymers of Polyvinylpyrrolidone

Contact Info

Product

Resources

About