Reduction of substrate-mode effects in power-combining arrays

Al-Zayed, Ayman S.; Swisher, Randall; Lécuyer, F.; Guyette, Andrew C.; Sun, Qi; Lisio, M.P. De

doi:10.1109/22.925492

Cited by 7 publications

(3 citation statements)

References 8 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Similar unit-cell-based methods can be used to model the stability of grid amplifiers [41]. Furthermore, a careful choice of the cell size can minimize the deleterious effects of substrate modes [42].…”

Section: Modelingmentioning

confidence: 99%

Quasi-optical and spatial power combining

DeLisio¹,

York

2002

IEEE Trans. Microwave Theory Techn.

172

View full text Add to dashboard Cite

Quasi-optical power-combining techniques have been developed to address fundamental limitations in solid-state devices and circuits. These techniques have been applied to oscillators, amplifiers, frequency-conversion components, and control circuits. This paper surveys progress in the development of quasi-optical array systems operating in the microwave and millimeter-wave regime, focusing primarily on the progress in power amplifiers.

show abstract

Section: Modelingmentioning

confidence: 99%

Quasi-optical and spatial power combining

DeLisio¹,

York

2002

IEEE Trans. Microwave Theory Techn.

172

View full text Add to dashboard Cite

show abstract

“…Several techniques have been presented to prevent different resonances in the substrates [4] by enabling higher order mode excitation, diode yield, and instabilities to be accounted for. We verified our model by means of a 72 dipole coupled HBV frequency tripler array, which was designed using the unit cell method [6].…”

Section: Introductionmentioning

confidence: 99%

Comparison of Full 3D and Unit Cell Models for Waveguide-Embedded Frequency Multiplier Arrays

Hrubo

Dahlbäck

Stake

2016

IEEE Microw. Wireless Compon. Lett.

View full text Add to dashboard Cite

“…These research investigations include increasing operating frequencies [I]- [2], optimizing for power and efficiency [3]- [4], improving bandwidth [SI, the removal of excess heat produced by the active devices [6], minimizing substrate mode effects [7] and others.…”

Section: Introouctionmentioning

confidence: 99%

Numerical and experimental investigation of losses in a tray based spatial power amplifier

Al-Zayed

Ortiz²,

Ozkar

et al.

IEEE MTT-S International Microwave Symposium Digest, 2003

Self Cite

View full text Add to dashboard Cite

4Abslracf -This paper presents experimental and numerical investigations on a 49-element Ka-band amplifier array. This study is aimed at determining the origin of various losses in the amplifier array. Passive simulation data confirms that the load seen by the active devices is well matched and that most of the power is coupled to the LSE,@ mode. This means that coherent power combining should take place if there is no phase and amplitude variation due to the active devices and phase correcting dielectric lenses. I. INTROOUCTIONSpatial (quasi-optical) power combining refers to combining the outputs of many active devices in free space. Several architectures have been developed for spatial power combining, integrating solid state devices to generate noteworthy power levels at a different range of frequency bands. Spatial combining also encompasses a broad rage of microwave circuits. These include amplifier, oscillators, beam controllers, and frequency converters.After much success in demonstrating the principles and concepts of spatial combining, researchers have directed there efforts on improving the structures and addressing important disadvantages and limitations associated with spatial power-combining techniques. These research investigations include increasing operating frequencies [I]-[2], optimizing for power and efficiency [3]-[4], improving bandwidth [SI, the removal of excess heat produced by the active devices [6], minimizing substrate mode effects [7] and others.The performance of a spatial amplifier array is affected by many factors. These factors are highly dependent on the type of amplifier array as well as the method of exciting the array. This paper studies the performance of the Ka-hand perpendicularly-fed patch amplifier array that is excited using a hard-hom antenna [2]. This amplifier can produce 6 watts of power, with a power combining efficiency of 39%.A drawing illustrating the concept for this amplifier array configuration is shown in Fig. 1. The patch antennas on the left of the diagram receive a signal radiated from 0-7803-769S-1/03/$17.00 0 2003 IEEE the transmitting hard hom. Each of the microstrip patch antennas is coupled to slot aperture, which then feeds a dielectric filled waveguide. The dielectric filled waveguide is then coupled to a microstrip line, which then feeds the MMIC amplifier. After amplification, the signal is radiated through the transmitting patch antenna in the same way that it was received. Finally, the signal radiated from the patch antennas are collected by a receiving hard hom located at the right of the figure. Hard-horns and dielectric lenses are used to provide a uniform amplitude and phase to the array of patch antennas, improving the combining efficiency of the system [8]-[9].

show abstract

Reduction of substrate-mode effects in power-combining arrays

Cited by 7 publications

References 8 publications

Quasi-optical and spatial power combining

Quasi-optical and spatial power combining

Comparison of Full 3D and Unit Cell Models for Waveguide-Embedded Frequency Multiplier Arrays

Numerical and experimental investigation of losses in a tray based spatial power amplifier

Contact Info

Product

Resources

About