Powder particle flow acceleration methods for simulation of interaction with materials used in spacecrafts

Lapkovskis, Vjačeslavs; Ушеренко, С. М.; Usherenko, Yulia; Mironovs, Viktors; Gluschenkov, V.

doi:10.15159/ar.19.213

Cited by 2 publications

(4 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Dynamic processing in SDP mode was carried out in the following conditions [39]: average particles speed 3000 m•s -1 , exposure time ~ 400 microseconds, the material of billets: carbon steel of ordinary quality St3 (0.14 -0.22%C, DIN St37-2), high-quality structural carbon steel 10 (0.07 -0.14%C, DIN C10) a high-speed steel W6Mo5Cr4V2 (DIN HS6-5-2), the material of powder particles -SiC, Ni and TiCN powder, 50-63 microns.…”

Section: Methodsmentioning

confidence: 99%

Dynamic Alloying of Steels in the Super-Deep Penetration Mode

Usherenko¹,

Mironovs²,

Ушеренко³

et al. 2022

Preprint

View full text Add to dashboard Cite

The dynamic effects observed in collisions represent a specific area of high-energy interaction located at the boundary of mechanics, hydrodynamics, shock wave physics, and alternating high-pressure regions. The paper shows that in the volume of a solid metal body, as a result of dynamic alloying by a high-speed stream of powder particles in the super-deep penetration mode (SDP), fibre structures of altering material arise, forming the framework of the composite material. The stream of powder particles in the metal obstacle following the path of least resistance and the impact of shock waves on particles results in a volumetric framework from the products of interaction between the injected and matrix materials. When using SDP, defective structural elements (channelled) - germs of reinforcing fibres arise. At the subsequent heat treatment, there is an intensive diffusion. The growth process of reinforcing fibres shifts to higher temperatures (as compared to the standard mode), leading to an increase in the bending strength of the fibre material up to 13 times for high-speed tool W6Mo5Cr4V2 steel. As a result of the completion of the growth of reinforcing fibres in the volume of the W6Mo5Cr4V2 steel, the material's bending strength in 1.2 times is realised. Simultaneously, it provides an increase of wear resistance 1.7-1.8 times.

show abstract

Section: Methodsmentioning

confidence: 99%

Dynamic Alloying of Steels in the Super-Deep Penetration Mode

Usherenko¹,

Mironovs²,

Ушеренко³

et al. 2022

Preprint

View full text Add to dashboard Cite

show abstract

“…Dynamic processing in SDP mode was carried out in the following conditions [ 39 ]: average particles speed 3000 m·s −1 , exposure time ~400 microseconds, the material of billets: carbon steel of ordinary quality St3 (0.14–0.22% C, DIN St37-2), high-quality structural carbon steel 10 (0.07–0.14% C, DIN C10), W6Mo5Cr4V2 (0.82–0.90% C, 5.5–6.5% W, 4.8–5.3% Mo, 3.8–4.4% Cr, 1.7–2.1% V) high-speed tool steel (DIN HS6-5-2). Cylindrical samples, diameter 30 mm, length 100 mm.…”

Section: Methodsmentioning

confidence: 99%

“… Outdoor explosive accelerator [ 39 ]: 1—initiator, 2—facing, 3—charge, 4—cumulative lens, 5—powder mixture, 6—plate-cartridge base, 7—adjusting support, and 8—sample. …”

Section: Figurementioning

confidence: 99%

See 1 more Smart Citation

Dynamic Alloying of Steels in the Super-Deep Penetration Mode

et al. 2022

View full text Add to dashboard Cite

The dynamic effects observed in collisions represent a specific area of high-energy interaction located at the boundary of mechanics, hydrodynamics, shock wave physics, and alternating high-pressure regions. The paper shows that in the volume of a solid metal body, as a result of dynamic alloying by a high-speed stream of powder particles in the super-deep penetration mode (SDP), fiber structures of altering material arise, forming the framework of the composite material. The stream of powder particles in the metal obstacle following the path of least resistance and the impact of shock waves on particles results in a volumetric framework from the products of interaction between the injected and matrix materials. When using SDP, defective structural elements (channeled)—germs of reinforcing fibers arise. At the subsequent heat treatment, there is an intensive diffusion. The growth process of reinforcing fibers shifts to higher temperatures (as compared to the standard mode), leading to an increase in the bending strength of the fiber material up to 13 times for W6Mo5Cr4V2 high-speed tool steel. As a result of the completion of the growth of reinforcing fibers in the volume of the W6Mo5Cr4V2 high-speed tool steel, the material’s bending strength in 1.2 times is realized. Simultaneously, it provides an increase of wear resistance 1.7–1.8 times.

show abstract

Powder particle flow acceleration methods for simulation of interaction with materials used in spacecrafts

Cited by 2 publications

References 0 publications

Dynamic Alloying of Steels in the Super-Deep Penetration Mode

Dynamic Alloying of Steels in the Super-Deep Penetration Mode

Dynamic Alloying of Steels in the Super-Deep Penetration Mode

Contact Info

Product

Resources

About