Performance Appraisals of Gas/Oil Separation Plants

Abstract

Summary Produced crude oil typically is processed at a wet-crude-handling facility (WCHF) or a gas/oil separation plant (GOSP). Most of the crude is commingled with water and produced in the form of emulsions that are separated at the GOSP using demulsifiers. In general, the emulsions at the inlet of Saudi Aramco GOSPs are tight, and no free water is observed in the feed stream. This paper describes the performance appraisal of several Saudi Aramco GOSPs. It also discusses the evaluation of these facilities and the efforts undertaken to reduce and optimize the costs of oil/water separation. The most important effort was the characterization of emulsions from various fields. It shows the relative tightness of emulsions and the associated causes of tightness. It has become a diagnostic tool in the quest to understand the causes and treatment of emulsions. The inlet emulsions were characterized by conducting field tests at each of the GOSPs using fresh emulsion samples. The factors associated with the tightness of emulsions include the amount of fine solids such as asphaltenes and scales in the crude, water cuts, temperature, brine chemistry, and shear. Another aspect of oil-water separation investigated was the effect of processing equipment and vessel retrofitting. These included the conversion of two-phase (gas/liquid) separators into three-phase (gas/oil/water) separators, installation of coalescer packs, demulsifier injection strategies, and use of online analyzers. An innovative approach to optimizing oil/water separation is described. The paper provides operational data including demulsifier-treatment costs per barrel of oil, invaluable experience, and many "lessons learned" that are applicable to other crude-oil-treating facilities. Introduction Crude oil is seldom produced alone and is generally commingled with water. Produced water occurs in two ways: Some of the water may be produced as free water (i.e., water that will settle out rapidly), and some of the water may be produced in the form of emulsions. Emulsions can be difficult to treat and can cause a number of operational challenges such as tripping of electrical grids in dehydrators/desalters, GOSP upsets, production of off-specification crude oil, and creating high pressure drops in flowlines. Emulsions have to be treated to remove the dispersed water and associated inorganic salts to meet crude specification for transportation, storage, and export, and to reduce corrosion and catalyst poisoning in downstream processing facilities. A typical Saudi Aramco GOSP consists of a 2- or 3-stage oil/gas-separation facility, with a 2- or 3-stage dehydrator/desalting train (Fig. 1). A typical GOSP processes between 100,000 and 300,000 B/D of crude and 100,000 B/D of water. The GOSPs are generally designed to handle water cuts to 30%, and some have been modified and retrofitted to handle higher watercuts. With increasing fluid throughputs, the GOSPs face a number of challenges mostly related to dehydration and desalting. These challenges include increased chemical consumption, possibility of increased water (and salt) carryover into the oil, oily effluent or disposal water, wide emulsion pads (rag layers), and electric-grid shorting. These challenges can cause operational upsets and lead to higher operating costs. During crude-oil processing at the GOSP, one of the most important variables that determines the efficiency of oil/water/gas separation is the tightness of the incoming emulsion. The tighter the emulsion, the higher the dosage of demulsifier needed to break them. The performance of the GOSP is closely tied to the characteristics of the feed emulsions. Therefore, one of the most important aspects of this study was to characterize the emulsions from every GOSP. Another aspect of GOSP performance is related to the process facilities (hardware) and process variables. The hardware includes the number and type of separators, dehydrators and desalters, water/oil separators (WOSs), and other hardware at the GOSP. Process variables include oil and water-flow rates, temperatures, water cuts, and GOSP operating conditions. A higher residence time of fluids in the GOSP will generally lead to better separation and better performance, all other variables being constant. Besides the residence time, process retrofits in the vessels also tend to enhance performance. The final, and important, part of the study was to identify and recommend new technologies for different types of on line analyzers and sensors. These include water-in-oil basic sediment-and-water (BS&W), oil-in-water, and salt-in-crude analyzers, and interface/emulsion probes/sensors for controlling demulsifier injection. The analyzers are meant to improve the monitoring of outlet crude and water specifications, and the sensors to be designated for improving GOSP performance through emulsion rag layer monitoring inside the vessels and automating demulsifier injection. This paper provides performance appraisals of individual GOSPs, recommends "best practices" for oil/water separation, and provides "lessons learned" to improve performance.

Application of DSC for Emulsified System Characterization

“…Effective separation of crude oil and water is an essential operation to ensure not only the quality of crude oil but also the quality of separated water phase at the lowest cost. Earlier studies [22,23] have shown the importance of emulsion characteristics on the performance and optimization of oil-water separation. Recently, in the framework of a joint study between IFP and Saudi Aramco, a strict and rigorous methodology was applied to gather information about the behavior and composition of Saudi Aramco emulsion samples collected from several Gas Oil Separation Plants [20,21].…”

Freezing Within Emulsions: Theoretical Aspects and Engineering Applications

“…Earlier studies [83,84] have shown the importance of emulsion characteristics on the performance and optimization of oil/water separation. The main objective is to provide recommendations to reduce treatment costs and optimize oil/water separation in the field.…”