Nuclear Magnetic Resonance Spectrometry

Dybowski, Cecil; Bruch, Martha D.

doi:10.1021/a1960007h

Cited by 6 publications

(3 citation statements)

References 215 publications

(178 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…MCC has been used as a reinforcing filler and binder for the extrusion/spheronization process. The origin of the raw materials and the manufacturing process decisively influence the characteristics of MCC [8].…”

Section: Introductionmentioning

confidence: 99%

Preparation of cellulose nanofibrils by high-pressure homogenizer and cellulose-based composite films

Lee¹,

Chun²,

Kang³

et al. 2009

Journal of Industrial and Engineering Chemistry

193

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 99%

Preparation of cellulose nanofibrils by high-pressure homogenizer and cellulose-based composite films

Lee¹,

Chun²,

Kang³

et al. 2009

Journal of Industrial and Engineering Chemistry

193

View full text Add to dashboard Cite

“…Matrix-assisted laser desorption/ionization (MALDI) time-of-flight mass spectrometry (TOF/MS) and electrospray ionization (ESI) mass spectrometry are techniques that have been increasingly applied to the characterization of dissolved macromolecules. Now applicable to a wide variety of polymers, these techniques can provide information complementary to traditional methods of polymer analysis such as size exclusion chromatography, infrared spectroscopy, and nuclear magnetic resonance …”

mentioning

confidence: 99%

“…Now applicable to a wide variety of polymers, these techniques can provide information complementary to traditional methods of polymer analysis such as size exclusion chromatography, 1 infrared spectroscopy, 2 and nuclear magnetic resonance. 3…”

mentioning

confidence: 99%

Desorption Behavior and Distributions of Fluorinated Polymers in MALDI and Electrospray Ionization Mass Spectrometry

et al. 1997

View full text Add to dashboard Cite

Matrix-assisted laser desorption/ionization (MALDI) and electrospray ionization (ESI) have been used to desorb fluorinated polymers for mass spectrometric analyses. Compounds with high fluorine content are insoluble or only sparingly soluble in conventional solvent systems, making them difficult candidates for mass spectrometry studies. Among 11 tested MALDI matrixes, 2,5-dihydroxybenzoic acid produced the highest ion yield for a model fluorinated analyte at a matrix/analyte molar ratio of 1000. Use of this matrix allowed determination of repeat units and the polymer distribution parameters: M n , M w , and D. In MALDI, solubility requirements for a fluorinated polymer may be incompatible with those of the matrix, potentially leading to inhomogeneous crystallization which may influence the observed distribution of oligomers. In ESI, when precipitation was not an overriding factor, a minimal aqueous content in the employed solvent vastly improved fluorinated polymer signal intensities compared to purely organic solvent systems. Dilution with small amounts of higher polarity solvents could promote the desorption of longer chain fluorocarbons, presumably due to augmented solvophobicity. However, a very high aqueous content (high polarity) may disfavor the desorption of longer chain fluorocarbons, especially at higher polymer concentrations. This latter observation has been attributed to preferential intermolecular aggregation of longer fluorocarbon chains. The presence of fluorinated groups offers the advantage of inductive stabilization of anionic charge sites for improved signals in negative ion MALDI and ESI, while low molecular weight halogenated solvents used for dissolution of fluorinated polymers can suppress the tendency toward discharge in negative ion ESI.Matrix-assisted laser desorption/ionization (MALDI) time-offlight mass spectrometry (TOF/MS) and electrospray ionization (ESI) mass spectrometry are techniques that have been increasingly applied to the characterization of dissolved macromolecules. Now applicable to a wide variety of polymers, these techniques can provide information complementary to traditional methods of polymer analysis such as size exclusion chromatography, 1 infrared spectroscopy, 2 and nuclear magnetic resonance. 3

show abstract