Modulated circulation control around the blades of a vertical axis hydrokinetic turbine for flow control and improved performance

Gorle, J.M.R.; Chatellier, Ludovic; Pons, Frédéric; Ba, M.

doi:10.1016/j.rser.2019.02.007

Cited by 6 publications

(3 citation statements)

References 64 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In addition, a k-ω SST turbulence model is also applicable to complex flow, such as the Fluid-Solid Interaction (FSI) issues [29] and the flow across the Darrieus turbine [30,31]. Furthermore, there is also a good agreement between the numerical simulation results and experimental data reported in the previous works.…”

Section: Introductionmentioning

confidence: 54%

Numerical Investigation of Vortex Shedding from a 5:1 Rectangular Cylinder at Different Angles of Attack

Liu

Zhang

et al. 2022

JMSE

View full text Add to dashboard Cite

Although flow around a 5:1 rectangular cylinder at small angles of attack (AoA) has been extensively studied, when the AoA becomes larger, the research is rare. Therefore, this study performs Unsteady Reynolds-Averaged Navier-Stokes simulations (URANS) using the k-ω SST turbulence model for unsteady flow around a two-dimensional 5:1 rectangular cylinder at different AoAs up to 45°. A strong dependence of the flow characteristics on AoA is observed through the analysis of the time-averaged lift coefficient, drag coefficient, and Strouhal number. The peak of lift and drag coefficient is observed to be correlated, respectively, to the leading- and trailing-edge vortex based on the analysis of the flow. The x′-directional length of the main recirculation bubble on the top side and the distance from the bubble center to the leading edge of the cylinder both reach the maximum when α = 15°. In addition, the standard deviation σx' of the time-averaged velocity U¯x' along the cylinder shows a trend of increasing at first and then decreasing, and that σy' also shows the same trend at α = 20°~45°; it fluctuates within a range of 0.05~0.2 at α = 0°~20°. Finally, two principal modes of vortex shedding are observed with α = 15° being their turning point, (i) “1 + 1” mode: in one vortex shedding period, two major vortices shed off from the top and bottom sides of the cylinder at α ≤ 15°; (ii) “2 + 2” mode, four vortices shed off from the top and bottom sides of the cylinder at α > 15° in one vortex shedding period.

show abstract

Section: Introductionmentioning

confidence: 54%

Numerical Investigation of Vortex Shedding from a 5:1 Rectangular Cylinder at Different Angles of Attack

Liu

Zhang

et al. 2022

JMSE

View full text Add to dashboard Cite

show abstract

“…• Horizontal axis turbine [116][117][118]-blades, driven by current energy, rotate around the horizontal axis; • Vertical axis turbine [119][120][121][122][123][124]-blades, driven by current energy, rotate around the vertical axis; •…”

Section: Tidal Current and Ocean Current Energy Conversionmentioning

confidence: 99%

Ocean Renewable Energy Potential, Technology, and Deployments: A Case Study of Brazil

Shadman

Silva

Faller³

et al. 2019

Energies

View full text Add to dashboard Cite

This study, firstly, provides an up-to-date global review of the potential, technologies, prototypes, installed capacities, and projects related to ocean renewable energy including wave, tidal, and thermal, and salinity gradient sources. Secondly, as a case study, we present a preliminary assessment of the wave, ocean current, and thermal gradient sources along the Brazilian coastline. The global status of the technological maturity of the projects, their different stages of development, and the current global installed capacity for different sources indicate the most promising technologies considering the trend of global interest. In Brazil, despite the extensive coastline and the fact that almost 82% of the Brazilian electricity matrix is renewable, ocean renewable energy resources are still unexplored. The results, using oceanographic fields produced by numerical models, show the significant potential of ocean thermal and wave energy sources in the northern and southern regions of the Brazilian coast, which could contribute as complementary supply sources in the national electricity matrix.

show abstract

“…A two-dimensional CFD simulation was performed, in which the overset technique was used in order to model not only the rotation of the blades but also the pitching motion. Numerical results showed very interesting findings about the controlled flow and the versatility of overset mesh in the study of flow control for VAT based on circulation control; nevertheless, no details of a convergence analysis and the number of meshes were provided [30].…”

Section: Introductionmentioning

confidence: 99%

Comparison of Sliding and Overset Mesh Techniques in the Simulation of a Vertical Axis Turbine for Hydrokinetic Applications

Mejia

Escorcia

et al. 2021

Processes

View full text Add to dashboard Cite

The application of Computational Fluid Dynamics (CFD) to energy-related problems has increased in the last decades in both renewable and conventional energy conversion processes. In recent years, the application of CFD in the study of hydraulic, marine, tidal, and hydrokinetic turbines has focused on the understanding of the details of the complex turbulent flow and also in improving the prediction of the performance of these devices. There are several complexities involved in the simulation of Vertical Axis Turbine (VAT) for hydrokinetic applications. One of them is the necessity of a dynamic mesh model. Typically, the model used in the simulation of these devices is the sliding mesh technique, but in recent years the fast development of the overset (also known as chimera) mesh technique has caught the attention of the academic community. In the present paper, a comparison between these two techniques is done in order to establish their advantages and disadvantages in the two-dimensional simulation of vertical axis turbines. The comparison was done not only for the prediction of performance parameters of the turbine but also for the capabilities of the models to capture complex flow phenomena in these devices and computational costs.

show abstract

Modulated circulation control around the blades of a vertical axis hydrokinetic turbine for flow control and improved performance

Cited by 6 publications

References 64 publications

Numerical Investigation of Vortex Shedding from a 5:1 Rectangular Cylinder at Different Angles of Attack

Numerical Investigation of Vortex Shedding from a 5:1 Rectangular Cylinder at Different Angles of Attack

Ocean Renewable Energy Potential, Technology, and Deployments: A Case Study of Brazil

Comparison of Sliding and Overset Mesh Techniques in the Simulation of a Vertical Axis Turbine for Hydrokinetic Applications

Contact Info

Product

Resources

About