Microstructural design and additive manufacturing and characterization of 3D orthogonal short carbon fiber/acrylonitrile-butadiene-styrene preform and composite

Quan, Zhenzhen; Larimore, Zachary; Wu, Amanda S.; Yu, Jianyong; Qin, Xiaohong; Mirotznik, Mark S.; Suhr, Jonghwan; Byun, Joon‐Hyung; Oh, Youngseok; Chou, Tsu‐Wei

doi:10.1016/j.compscitech.2016.02.021

Cited by 113 publications

(75 citation statements)

References 29 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…According to figure 3, PER additions caused decrease for storage modulus of unfilled ABS. 15% PER containing composite yield nearly identical storage modulus value with that of ABS due to restriction effect of PER particles on segmental mobility of ABS chains [41][42][43].…”

Section: Dma Studymentioning

confidence: 91%

Mechanical, thermo-mechanical and morphological characterization of ABS based composites loaded with perlite mineral

Alghadi

Tirkeş

Tayfun³

2019

Mater. Res. Express

View full text Add to dashboard Cite

Acrylonitrile-butadiene-styrene (ABS) copolymer was filled with perlite mineral (PER) at four different loading level of 2.5%, 5%, 10% and 15%. ABS/PER composites were produced using labscale micro-compounder followed by injection molding process. Mechanical, thermo-mechanical, melt-flow and morphological properties of composites were reported by tensile and impact tests, dynamic mechanical analysis (DMA), melt flow index (MFI) test and scanning electron microscopy (SEM), respectively. Mechanical characterizations revealed that tensile strength, elongation and Youngs' modulus of ABS were improved by PER inclusions. However, impact strength of ABS reduced with increase of PER concentration. Glass transition temperature of ABS displayed increasing trend for %5 concentration of PER. MFI test implied that PER addition caused slight decreasing for MFI value of unfilled ABS. Homogeneous dispersion of PER particles into ABS matrix for their lower loading level was obtained from SEM micrographs of composites. According to findings, 5% PER containing sample exhibited the best performance and it was remarked as the most suitable candidate among fabricated ABS based composites.

show abstract

Section: Dma Studymentioning

confidence: 91%

Mechanical, thermo-mechanical and morphological characterization of ABS based composites loaded with perlite mineral

Alghadi

Tirkeş

Tayfun³

2019

Mater. Res. Express

View full text Add to dashboard Cite

show abstract

“…The deposition minimizes interaction of polymer chains between adjacent layers, which limits entanglement across this interface . Carbon fiber in melt would be oriented along the flow direction because of shear force, and the orientation can be preserved due to the big viscosity and the slow rate of polymer melt before the molten cools to a clot . An additively manufactured continuous fiber reinforced sandwich part was reported in Ref.…”

Section: Introductionmentioning

confidence: 99%

“…Quan et al . reported microstructural design and characterization of 3D orthogonal short carbon fiber/ABS preform and composite …”

Section: Introductionmentioning

confidence: 99%

Anisotropy of poly(lactic acid)/carbon fiber composites prepared by fused deposition modeling

Ding

Zhang

et al. 2019

J of Applied Polymer Sci

View full text Add to dashboard Cite

It is well known that 3D printed parts prepared by fused deposition modeling (FDM) exhibit large anisotropy of mechanical properties. In this article, poly(lactic acid; PLA)/carbon fiber (CF) composites with different built orientations (X, Y, Z) were prepared by FDM. The effects of printing temperature, speed, orientations, and layer thickness on the mechanical properties of the composites were systematically investigated. The mechanical properties of PLA/CF composites show more significant anisotropy. The orientation of the fibers along the printing direction is displayed by scanning electron microscopy. Printing parameters bring almost no effect on mechanical properties of the X‐construct oriented specimen, and bring obvious effect on those of the Y‐construct oriented specimen and Z‐construct oriented specimen. According to the analysis, carbon fiber can amplify this anisotropy from layer fashion, and the key factors from printing parameters are porosity and bond strength between fuses. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48786.

show abstract

“…Four types of specimens as shown in Table 1 were additively manufactured using fused filament fabrication approach [30,31]. The structural parameters were depicted in Fig.…”

Section: Additive Manufacturingmentioning

confidence: 99%

“…In order to explore opportunities for additive manufacturing of multidirectional preforms for composites, Quan et al recently demonstrated the fabrication of an array of preforms via fused filament fabrication (FFF) [30] and reported their results on microstructural design and additive manufacturing and characterization of short carbon fiber/acrylonitrile-butadiene-styrene (ABS) 3D orthogonal preforms and composites [31]. Although high model-to-part fidelity was observed, the microstructure and interfaces of additively manufactured preforms and composites were not characterized.…”

Section: Introductionmentioning

confidence: 99%

Microstructural characterization of additively manufactured multi-directional preforms and composites via X-ray micro-computed tomography

Quan

Larimore

Qin

et al. 2016

Composites Science and Technology

Self Cite

View full text Add to dashboard Cite

Microstructural design and additive manufacturing and characterization of 3D orthogonal short carbon fiber/acrylonitrile-butadiene-styrene preform and composite

Cited by 113 publications

References 29 publications

Mechanical, thermo-mechanical and morphological characterization of ABS based composites loaded with perlite mineral

Mechanical, thermo-mechanical and morphological characterization of ABS based composites loaded with perlite mineral

Anisotropy of poly(lactic acid)/carbon fiber composites prepared by fused deposition modeling

Microstructural characterization of additively manufactured multi-directional preforms and composites via X-ray micro-computed tomography

Contact Info

Product

Resources

About