Microstrip Patch Antenna for the Applications of WLAN Systems using S-Band

Mahbub, Fardeen; Akash, Shouherdho Banerjee; Al-Nahiun, Sayed Abdul Kadir; Islam, Rashedul; Hasan, Raja Rashidul; Rahman, Md. Abdur

doi:10.1109/ccwc51732.2021.9376114

Cited by 14 publications

(2 citation statements)

References 7 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Research by Mahbub et al [19] shows how the software that comes with the CST studio suite 2016 was used to make a rectangular MPA. This was done since the future of wireless local-area network (WLAN) systems would require improved gain and efficiency.…”

Section: Literature Reviewmentioning

confidence: 99%

A 2.45 GHz microstrip patch antenna design, simulation, and anlaysis for wireless applications

et al. 2023

View full text Add to dashboard Cite

This paper designs, simulates, and analyzes the S-band microstrip patch antenna (MPA) for wireless applications. FR-4 (lossy) and Rogger RT/duroid, whose dielectric permittivity is 4.3 and 2.2, respectively, have been used as substrate materials. Simulation is done by computer simulation technology (CST) suite studio 2019 software. Simulations with FR-4 material showed that the return loss was -20.405 dB, the gain was 2.592 dB, the directivity was 7.47 dBi, the voltage standing wave ratio (VSWR) was 1.221, the bandwidth (BW) was 0.0746 GHz, and the efficiency was 34.69%. Also, Rogers RT/duroid material gives results of a return loss of -12.542 dB, a bandwidth (BW) of 0.0349 GHz, a gain of 8.092 dB, a directivity of 8.587 dBi, and an efficiency of 94.24%. The main goal of this antenna is to have a low return loss while getting as close as possible to a VSWR of 1. This will improve the antenna's gain, directivity, and efficiency compared to other antennas. Copper was used to make the patch and the ground, which were 0.35 mm and 0.0077 mm thick, respectively. The results obtained from the proposed antenna were better than those previously published in various in modern scientific journal and conference papers.

show abstract

Section: Literature Reviewmentioning

confidence: 99%

A 2.45 GHz microstrip patch antenna design, simulation, and anlaysis for wireless applications

et al. 2023

View full text Add to dashboard Cite

show abstract

“…There are some critical periods in these missions where continuous telemetry is obligatory [18]. As the size and weight constraints are obvious given the fact that the antenna must be compact enough to be mounted inside a minimizing wireless communication device [19], an S-Band antenna adhering to these constraints is addressed in this paper. Hence, the proposed antenna for telemetry applications is of small size and simultaneously has better performance characteristics such as wide-band and nearly omnidirectional radiation pattern.…”

Section: Introductionmentioning

confidence: 99%

Design of Wide-Band Microstrip Antenna for S-Band Telemetry Applications

Pushpalatha

Namana

Navadagi

et al. 2023

AEM

View full text Add to dashboard Cite

This paper exemplifies the design of a low profile wide-band microstrip antenna suitable for S-Band telemetry applications. The proposed design explores the concept of wide-band antenna with improved omnidirectional gain and smaller size essentially aiming at low-earth orbit (LEO) satellite telemetry. The proposed partial annular radiating patch design has an operating impedance bandwidth ranging from 2.7 GHz to 3.8 GHz with a percentage bandwidth of 31%. It exhibits vertical polarization with a gain of around 1.434 dBi. The design and simulations are carried out using 3D EM tools and the measurement results for various performance metrics of the antenna are validated with the simulation results.

show abstract