Mechanical performance of hybrid bismaleimide composites reinforced with three-dimensional braided carbon and Kevlar fabrics

Wan, Yizao; Wang, Y.L.; He, Fang; Huang, Yuan; Jiang, Huan

doi:10.1016/j.compositesa.2006.02.021

Cited by 51 publications

(22 citation statements)

References 53 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In the melt mixing processes, polymer molecules gain increased mobility through an input of thermal energy and are mixed with the fillers mechanically. In fact, melt mixing is the most favored technique to prepare the contemporary BMI-based nanocomposites [61][62][63][64]. As an example, Meng et al [62] prepared the BMI-DABPA(O,Odiallyl bisphenol A)-clay nanocomposite by first homogenously mixing DABPA and clay (2 hours), followed by melt mixing of the mixture with BMI at 130 • C. Mechanical stirrer or high-speed homogenizers are usually employed to facilitate the homogenous mixing of fillers within polymer melts.…”

Section: Methods For Dispersing Silica Nanoparticles In Polymermentioning

confidence: 99%

Synthesis of Silica Nanoparticles by Sol‐Gel: Size‐Dependent Properties, Surface Modification, and Applications in Silica‐Polymer Nanocomposites—A Review

Rahman

Padavettan

2012

Journal of Nanomaterials

858

462

View full text Add to dashboard Cite

Application of silica nanoparticles as fillers in the preparation of nanocomposite of polymers has drawn much attention, due to the increased demand for new materials with improved thermal, mechanical, physical, and chemical properties. Recent developments in the synthesis of monodispersed, narrow-size distribution of nanoparticles by sol-gel method provide significant boost to development of silica-polymer nanocomposites. This paper is written by emphasizing on the synthesis of silica nanoparticles, characterization on size-dependent properties, and surface modification for the preparation of homogeneous nanocomposites, generally by sol-gel technique. The effect of nanosilica on the properties of various types of silica-polymer composites is also summarized.

show abstract

Section: Methods For Dispersing Silica Nanoparticles In Polymermentioning

confidence: 99%

Synthesis of Silica Nanoparticles by Sol‐Gel: Size‐Dependent Properties, Surface Modification, and Applications in Silica‐Polymer Nanocomposites—A Review

Rahman

Padavettan

2012

Journal of Nanomaterials

858

462

View full text Add to dashboard Cite

show abstract

“…Indeed, fiber hybridization offers a comprehensive set of possibilities leading to synergetic effects or to properties not exhibited by the single constituents [3]. This approach has been successfully exploited in the field of low-velocity impact resistance of composite laminates [4], with the first studies aimed at increasing the damage tolerance of carbon fiber composites by adding more ductile fibers, mainly glass [5][6][7] and aramid [8][9][10][11][12]. Recently new fiber combinations have been investigated, mainly based on natural and synthetic fibers.…”

Section: Introductionmentioning

confidence: 99%

Quasi-Static and Low-Velocity Impact Behavior of Intraply Hybrid Flax/Basalt Composites

Sarasini

Tirillò

Ferrante

et al. 2019

Fibers

View full text Add to dashboard Cite

In an attempt to increase the low-velocity impact response of natural fiber composites, a new hybrid intraply woven fabric based on flax and basalt fibers has been used to manufacture laminates with both thermoplastic and thermoset matrices. The matrix type (epoxy or polypropylene (PP) with or without a maleated coupling agent) significantly affected the absorbed energy and the damage mechanisms. The absorbed energy at perforation for PP-based composites was 90% and 50% higher than that of epoxy and compatibilized PP composites, respectively. The hybrid fiber architecture counteracted the influence of low transverse strength of flax fibers on impact response, irrespective of the matrix type. In thermoplastic laminates, the matrix plasticization delayed the onset of major damage during impact and allowed a better balance of quasi-static properties, energy absorption, peak force, and perforation energy compared to epoxy-based composites.

show abstract

“…Addition of ductile fiber improved its impact properties significantly of all carbon composites. As the volume of the relative Kevlar fiber increased, residual flexure and energy absorption also increased which were tested with the impact samples [9].…”

Section: Literature Surveymentioning

confidence: 99%

A Research on Kevlar and Hybrid Kevlar Composites; A Report

2019

ijrte

View full text Add to dashboard Cite

This study focused on the Kevlar fiber composite, the demand of Kevlar composites increasing day-byday because it’s light weight and good mechanical properties. There are different types of fiber composites are available like Carbon, Basalt, Glass, Jute, Kenaf, Flax, Hemp and Kevlar etc. Out of these available material Kevlar is one of the most favorable composite material. Properties of Kevlar include high rigidity modulus, toughness, thermal stability and most importantly strength. Moreover, the properties of Kevlar composite can be increased by applying the different hybridization and treatment process. The aim of this study, to explore the different types of hybridization and treatments that can be applied for improving the mechanical properties of Kevlar composite

show abstract

Mechanical performance of hybrid bismaleimide composites reinforced with three-dimensional braided carbon and Kevlar fabrics

Cited by 51 publications

References 53 publications

Synthesis of Silica Nanoparticles by Sol‐Gel: Size‐Dependent Properties, Surface Modification, and Applications in Silica‐Polymer Nanocomposites—A Review

Synthesis of Silica Nanoparticles by Sol‐Gel: Size‐Dependent Properties, Surface Modification, and Applications in Silica‐Polymer Nanocomposites—A Review

Quasi-Static and Low-Velocity Impact Behavior of Intraply Hybrid Flax/Basalt Composites

A Research on Kevlar and Hybrid Kevlar Composites; A Report

Contact Info

Product

Resources

About