Material characteristics of the LTCC base material CeramTape GC

Franz, Manuela; Atassi, Ibrahim; Marić, Andrea; Balluch, Bruno; Weilguni, Michael; Smetana, Walter; Kluge, Christian; Radosavljevic, Goran

doi:10.1109/isse.2012.6273086

Cited by 12 publications

(11 citation statements)

References 5 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…7), and with the data obtained in [3], at values over 3 GHz the permittivity characteristic is diminished, along with the increase of dielectric losses. At working domain of 1MHz -1GHz -in range of RFID applications, see [6][7][8], the results are very promising. The characteristics present a clear linearity and a relatively low dependence of external temperature (here 10 -30 º C, common for medical applications), Fig.…”

Section: Technological Integrationmentioning

confidence: 99%

Sensors in LTCC-technology with embedded microfluidic features, for medical applications

Ciobanu

Schreiner

Vasile

et al. 2015

2015 IEEE International Symposium on Medical Measurements and Applications (MeMeA) Proceedings

View full text Add to dashboard Cite

The lab-on-chip testing units based on microfluidics technology are booming nowadays, due to robustness, simplicity of use and reliability. Multilayer ceramics, functionalized with nano-scaled sensing materials, and further integrated within microfluidic test elements, are of great challenge and represent the purpose of the paper. The LTCC technology versatility allows the 3D integration of electrochemical sensors with microfluidic features, and further with advanced signal processing and wireless communication.This full text paper was peer-reviewed at the direction of IEEE Instrumentation and Measurement Society prior to the acceptance and publication.978-1-4799-6477-2/15/$31.00 ©2015 IEEE

show abstract

Section: Technological Integrationmentioning

confidence: 99%

Sensors in LTCC-technology with embedded microfluidic features, for medical applications

Ciobanu

Schreiner

Vasile

et al. 2015

2015 IEEE International Symposium on Medical Measurements and Applications (MeMeA) Proceedings

View full text Add to dashboard Cite

show abstract

“…The main properties of used materials' dielectric tape and conductive paste are presented in Tables and , respectively. Geometrical and electrical properties of tape and paste which were chosen for inductor fabrication do not change significantly in the frequency range of interest and for that reason were considered a constant …”

Section: Design Of Inductorsmentioning

confidence: 99%

“…Dielectric Ceramtape GC tapes are used for the formation of the dielectric stack, while different combinations of ESL 40011 and ESL 40012 are chosen for the formation of ferrite cores. Ceramtape GC is a glass ceramic made of alumina and anorthite . Both ESL 40011 and ESL 40012 tapes are fundamentally Fe‐Ni‐Zn ferrites with different concentrations of the same basic compound.…”

Section: Fabrication Of Designed Inductorsmentioning

confidence: 99%

“…Geometrical and electrical properties of tape and paste which were chosen for inductor fabrication do not change significantly in the frequency range of interest and for that reason were considered a constant. [15][16][17] Properties of proposed solenoid geometry are initially estimated by means of electromagnetic simulation. The commercial electromagnetic simulator (Microwave Office MWO, AWR, El Segundo, CA) 19 has been used for this purpose.…”

Section: Design Of Inductorsmentioning

confidence: 99%

“…Ceramtape GC is a glass ceramic made of alumina and anorthite. 15 Both ESL 40011 and ESL 40012 tapes are fundamentally Fe-Ni-Zn ferrites with different concentrations of the same basic compound. Small amount of added copper can be found in both ferrite tapes, although negligible traces of aluminum (0.65%) are additionally detected in ESL 40012.…”

Section: Fabrication Of Designed Inductorsmentioning

confidence: 99%

See 2 more Smart Citations

Fine Tuning of 3D LTCC Inductor Properties Using Combination of Different Ferrite and Dielectric Tapes

Marić

Blaz

Živanov

et al. 2014

Int J Applied Ceramic Tech

View full text Add to dashboard Cite

Presented research offers solutions for properties alternation of 3D LTCC inductors by variation of materials implemented for their fabrication. Investigated geometry is solenoid‐shape micro‐inductor. Two types of dielectric cores are applied to achieve increase of quality factor for over 40% at GHz range. Five different stacks of ferrite material combinations are implemented when either fine inductance adjustments are needed or in cases when higher quality factor is required at MHz range frequencies. Increase of starting inductance of solid dielectric core solenoid is realized in tuning range of (35–60) %. Different ferrite core configurations can double quality factor maximum.

show abstract

Wet chemical porosification with phosphate buffer solutions for permittivity reduction of LTCC substrates

Hajian

Konegger

Bielecki

et al. 2021

Journal of Alloys and Compounds

View full text Add to dashboard Cite

Material characteristics of the LTCC base material CeramTape GC

Cited by 12 publications

References 5 publications

Sensors in LTCC-technology with embedded microfluidic features, for medical applications

Sensors in LTCC-technology with embedded microfluidic features, for medical applications

Fine Tuning of 3D LTCC Inductor Properties Using Combination of Different Ferrite and Dielectric Tapes

Wet chemical porosification with phosphate buffer solutions for permittivity reduction of LTCC substrates

Contact Info

Product

Resources

About