Magnetic microactuation of polysilicon flexure structures

Judy, Jack W.; Muller, R.S.; Zappe, H. H.

doi:10.1109/84.475542

Cited by 141 publications

(84 citation statements)

References 17 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…High-aspect-ratio ferromagnetic structures have been shown to rotate within a magnetic field to align their long axis with the magnetic field vector. [28] When the structures were placed on top of a permanent magnet the paddles were observed to rotate about their long axis (Fig. 2).…”

mentioning

confidence: 99%

A Gecko‐Inspired Reversible Adhesive

et al. 2008

View full text Add to dashboard Cite

A synthetic, fully reversible, switchable, gecko‐inspired adhesive is presented. The biomimetic system is composed of flexible nickel paddles coated with aligned vertical polymeric nanorods. When subjected to a magnetic field, adhesion decreases by a factor of 40. The ability of the adhesive to controllably stick and release from a surface could enable technologies from ubiquitous latching systems to climbing microrobotics.

show abstract

mentioning

confidence: 99%

A Gecko‐Inspired Reversible Adhesive

et al. 2008

View full text Add to dashboard Cite

show abstract

“…A scanning angle of 20 and scan range up to 2 kHz have been achieved with a power less than 1 W [91]. Electromagnetic scanning mirrors have also been reported [92], [93]. Fig.…”

Section: Optical Scannersmentioning

confidence: 86%

Micromachining for optical and optoelectronic systems

1997

Proc. IEEE

246

101

View full text Add to dashboard Cite

“…Impact drive mechanisms [139], [140], [141] and electromagnetic actuators [142], [143] have been implemented at micron scales as well. Magnetically anisotropic materials such as nickel-iron films and polymer magnets can be electroplated or otherwise deposited onto microstructures and subsequently actuated by external fields [144], [145].…”

Section: Micro-scale Actuatorsmentioning

confidence: 99%

Single‐Chip Scanning Probe Microscopes

Sarkar

Mansour²

2015

Micro‐ and Nanomanipulation Tools

View full text Add to dashboard Cite

Scanning probe microscopes (SPMs) are the highest resolution imaging instruments available today and are among the most important tools in nanoscience. Conventional SPMs suffer from several drawbacks owing to their large and bulky construction and to the use of piezoelectric materials. Large scanners have low resonant frequencies that limit their achievable imaging bandwidth and render them susceptible to disturbance from ambient vibrations. Array approaches have been used to alleviate the bandwidth bottleneck; however as arrays are scaled upwards, the scanning speed must decline to accommodate larger payloads. In addition, the long mechanical path from the tip to the sample contributes thermal drift. Furthermore, intrinsic properties of piezoelectric materials result in creep and hysteresis, which contribute to image distortion. The tip-sample interaction signals are often measured with optical configurations that require large free-space paths, are cumbersome to align, and add to the high cost of state-of-the-art SPM systems. These shortcomings have stifled the widespread adoption of SPMs by the nanometrology community. Tiny, inexpensive, fast, stable and independent SPMs that do not incur bandwidth penalties upon array scaling would therefore be most welcome. A method to increase the quality factor (Q-factor) of flexural resonators is introduced. The method relies on an internal energy pumping mechanism that is based on the interplay between electrical, iv mechanical, and thermal effects. To the best of the author's knowledge, the devices that are designed to harness these effects possess the highest electromechanical Qs reported for flexural resonators operating in air; electrically measured Q is enhanced from ~50 to ~50,000 in one exemplary device. A physical explanation for the underlying mechanism is proposed.The design, fabrication, imaging, and tip-based lithographic patterning with the first single-chip Scanning Thermal Microscopes (SThMs) are also presented. In addition to 3 DOF scanning, these devices possess integrated, thermally isolated temperature sensors to detect heat transfer in the tip-sample region.Imaging is reported with thermocouple-based devices and patterning is reported with resistive heater/sensors. An "isothermal electrothermal scanner" is designed and fabricated, and a method to operate it is detailed. The mechanism, based on electrothermal actuation, maintains a constant temperature in a central location while positioning a payload over a range of >35μm, thereby suppressing the deleterious thermal crosstalk effects that have thus far plagued thermally actuated devices with integrated sensors.

show abstract

Magnetic microactuation of polysilicon flexure structures

Cited by 141 publications

References 17 publications

A Gecko‐Inspired Reversible Adhesive

A Gecko‐Inspired Reversible Adhesive

Micromachining for optical and optoelectronic systems

Single‐Chip Scanning Probe Microscopes

Contact Info

Product

Resources

About