Investigation on Interface Temperature and Parametric Optimization During Machining of Reduced Graphene Oxide Nanoflakes Dispersed Polymer-based Carbon Fiber Reinforced (rGO/CF) Nanocomposites

Kesarwani, Shivi; Verma, Rajesh Kumar

doi:10.1007/s12633-022-01844-y

Cited by 5 publications

(3 citation statements)

References 56 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Considering these factors together for the analysis of the erosive wear test is a cumbersome process. To ease the calculation, the Taguchi strategy was applied to the control factors as categorized using L 16 orthogonal array, Table 2 [36]. The signal to noise ratio was utilised to assess each experiment's effectiveness.…”

Section: Taguchi Analysismentioning

confidence: 99%

Physical and mechanical characterization of glass fiber‐grewia optiva fiber reinforced hybrid polymer composite fabricated by vacuum assisted resin transfer moulding

Verma,

Gupta,

Gangil

2023

Materialwissenschaft Werkst

View full text Add to dashboard Cite

The natural and synthetic fibers are combined in a single composite to achieve a balance between the desired strength and cost considerations. In this study, the vacuum resin transfer moulding process was used to prepare an epoxy‐based composite. The composite consisted of grewia optiva as the natural fiber and glass fiber as the synthetic fiber, both with a fixed weightage of 10 %. Dolomite was used as a filler with varying content (0 %, 5 %, 10 %, and 15 weight %). The physical, mechanical, erosion wear and morphological behavior of the epoxy‐based composite were investigated. The inclusion of dolomite filler significantly increased the composite hardness and impact strength but reduced its tensile and flexural strength. At a dolomite filler content of 10 weight %, the erosive wear was reduced, while it increased at higher dolomite filler contents. The composite was examined using the L16 array, and the minimum wear rate was observed at an impingement angle of 30°, a velocity of 10 m/s, and an erodent size of 150 μm. Morphological studies were conducted to explore the possible mechanism for the variation in erosive wear at different dolomite contents in the hybrid composites.

show abstract

Section: Taguchi Analysismentioning

confidence: 99%

Physical and mechanical characterization of glass fiber‐grewia optiva fiber reinforced hybrid polymer composite fabricated by vacuum assisted resin transfer moulding

Verma,

Gupta,

Gangil

2023

Materialwissenschaft Werkst

View full text Add to dashboard Cite

show abstract

“…Graphene exists in the form of graphene oxide, graphene nanoplatelets, graphene nanoribbon, reduced graphene oxide, graphene quantum dots, etc. 20 Graphene is widely used in transistors, lithium-sulphur (Li-S) batteries, sensors, displays, etc. Graphene materials have also been investigated for solar cell applications because of their enhanced optical transparency, higher mechanical strength, and fast carrier mobility.…”

Section: Introductionmentioning

confidence: 99%

“…Graphene exists in the form of graphene oxide, graphene nanoplatelets, graphene nanoribbon, reduced graphene oxide, graphene quantum dots, etc. 20…”

Section: Introductionmentioning

confidence: 99%

Unleashing the solar revolution: harnessing the power of an ultra-strong tensile strength PGTPP nanocomposite photocatalyst for artificial photosynthesis

Kumar¹,

Yadav²,

Verma³

et al. 2023

Catal. Sci. Technol.

View full text Add to dashboard Cite

show abstract

Modified whale intelligence algorithm and Combined Compromise Solution (CoCoSo) for machinability evaluation of polymer nanocomposites

Kesarwani,

Verma,

2024

J Braz. Soc. Mech. Sci. Eng.

View full text Add to dashboard Cite

Investigation on Interface Temperature and Parametric Optimization During Machining of Reduced Graphene Oxide Nanoflakes Dispersed Polymer-based Carbon Fiber Reinforced (rGO/CF) Nanocomposites

Cited by 5 publications

References 56 publications

Physical and mechanical characterization of glass fiber‐grewia optiva fiber reinforced hybrid polymer composite fabricated by vacuum assisted resin transfer moulding

Physical and mechanical characterization of glass fiber‐grewia optiva fiber reinforced hybrid polymer composite fabricated by vacuum assisted resin transfer moulding

Unleashing the solar revolution: harnessing the power of an ultra-strong tensile strength PGTPP nanocomposite photocatalyst for artificial photosynthesis

Modified whale intelligence algorithm and Combined Compromise Solution (CoCoSo) for machinability evaluation of polymer nanocomposites

Contact Info

Product

Resources

About