Interface engineering of Li1.3Al0.3Ti1.7(PO4)3 ceramic electrolyte via multifunctional interfacial layer for all-solid-state lithium batteries

Jin, Yingmin; Liu, Chaojun; Zong, Xin; Li, Dong; Fu, Mengyu; Tan, Siping; Xiong, Yueping; Wei, Junhua

doi:10.1016/j.jpowsour.2020.228125

Cited by 63 publications

(42 citation statements)

References 37 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Few attempts have been made to combine polymer electrolytes with LATP to obtain solid electrolyte composites. Ma et al [390] paired a 10% LATP and polymer electrolyte/ionic liquid composite with a LiFePO 4 cathode and reported a capacity of 138 mAh g −1 after 250 cycles with 98% capacity retention at 60 • C. In addition, Wang et al [391] and Jin et al [392] studied LATP polymer composites. Yu and Manthiram [393] fabricated a slurry cast PEO-LiCF 3 SO 3 -LATP composite membrane solid electrolyte and paired it with a LiFePO 4 cathode.…”

Section: Li-analogues Of Nasiconmentioning

confidence: 99%

Sulfide and Oxide Inorganic Solid Electrolytes for All-Solid-State Li Batteries: A Review

et al. 2020

View full text Add to dashboard Cite

Energy storage materials are finding increasing applications in our daily lives, for devices such as mobile phones and electric vehicles. Current commercial batteries use flammable liquid electrolytes, which are unsafe, toxic, and environmentally unfriendly with low chemical stability. Recently, solid electrolytes have been extensively studied as alternative electrolytes to address these shortcomings. Herein, we report the early history, synthesis and characterization, mechanical properties, and Li+ ion transport mechanisms of inorganic sulfide and oxide electrolytes. Furthermore, we highlight the importance of the fabrication technology and experimental conditions, such as the effects of pressure and operating parameters, on the electrochemical performance of all-solid-state Li batteries. In particular, we emphasize promising electrolyte systems based on sulfides and argyrodites, such as LiPS5Cl and β-Li3PS4, oxide electrolytes, bare and doped Li7La3Zr2O12 garnet, NASICON-type structures, and perovskite electrolyte materials. Moreover, we discuss the present and future challenges that all-solid-state batteries face for large-scale industrial applications.

show abstract

Section: Li-analogues Of Nasiconmentioning

confidence: 99%

Sulfide and Oxide Inorganic Solid Electrolytes for All-Solid-State Li Batteries: A Review

et al. 2020

View full text Add to dashboard Cite

show abstract

“…Meanwhile, PEO adhesive was also employed as binder inside the cathode components (Figure 5B). The interfacial resistance of Li/LATP/Li battery was reduced from 2478 to 242 Ω and the LFP/LATP/Li full cell showed capacity retention of 97.3% at 0.3C after 100 cycles at 60 C. In order to enhance the mechanical strength of the PEO buffer layer, Jin et al 87 constructed a LATP nanoparticlereinforced polymer layer between LATP SSE and LFP cathode. Unfortunately, PEO-based polymer electrolytes are limited by their poor electrochemical window, which reduced their compatibility with high-voltage cathodes severely.…”

Section: Interfaces Between Latp Sse and Cathodesmentioning

confidence: 99%

Progress and perspective of Li_1 + _xAl_xTi₂_‐x(PO₄)₃ ceramic electrolyte in lithium batteries

Yang

Chen

et al. 2021

InfoMat

View full text Add to dashboard Cite

The replacement of liquid organic electrolytes with solid-state electrolytes (SSEs) is a feasible way to solve the safety issues and improve the energy density of lithium batteries. Developing SSEs materials that can well match with high-voltage cathodes and lithium metal anode is quite significant to develop high-energy-density lithium batteries. Li 1 + x Al x Ti 2 -x (PO 4 ) 3 (LATP) SSE with NASICON structure exhibits high ionic conductivity, low cost and superior air stability, which enable it as one of the most hopeful candidates for all-solidstate batteries (ASSBs). However, the high interfacial impedance between LATP and electrodes, and the severe interfacial side reactions with the lithium metal greatly limit its applications in ASSBs. This review introduces the crystal structure and ion transport mechanisms of LATP and summarizes the key factors affecting the ionic conductivity. The side reaction mechanisms of LATP with Li metal and the promising strategies for optimizing interfacial compatibility are reviewed. We also summarize the applications of LATP including as surface coatings of cathode particles, ion transport network additives and inorganic fillers of composite polymer electrolytes. At last, this review proposes the challenges and the future development directions of LATP in SSBs. K E Y W O R D Scrystal structure, interfaces, ionic conductivity, Li 1 + x Al x Ti 2 -x (PO 4 ) 3 , lithium batteries

show abstract

“…Besides, the well-matched CV curves from the first to the 30th cycle also demonstrate an outstanding electrochemical stability of PVDF/(PEO +PVDF)-L SCEs (Figure S10). 47…”

Section: ■ Results and Discussionmentioning

confidence: 99%

Double-Layer Solid Composite Electrolytes Enabling Improved Room-Temperature Cycling Performance for High-Voltage Lithium Metal Batteries

Zou

Shi

et al. 2021

ACS Omega

View full text Add to dashboard Cite

The development of solid-state electrolytes (SSEs) for high energy density lithium metal batteries (LMBs) usually needs to take into account of the interfacial compatibility against lithium metal and the electrolyte stability suitable for a high-potential cathode. In this study, through a facile two-step coating process, novel double-layer solid composite electrolytes (SCEs) with Janus characteristics are customized for the high-voltage LMBs with improved room-temperature cycling performance. Among which, high-voltage resistant poly(vinylidene fluoride) (PVDF) is adopted here for the construction of an electrolyte layer facing the cathode, while the other layer against the lithium anode is composed of the polymer matrix of poly(ethylene oxide) (PEO) blended with PVDF to obtain a lithium metal-friendly interface. With the further incorporation of Laponite clay, the PVDF/(PEO+PVDF)-L SCEs not only exhibit improved mechanical properties, but also achieve a highly increased ionic conductivity (5.2 × 10–4 S cm–1) and lithium ion migration number (0.471) at room temperature. The assembled NCM523|PVDF/(PEO+PVDF)-L SCEs|Li cells thus are able to deliver the initial discharge capacity of 153.9 mAh g–1 with 80.8% capacity retention after 200 cycles at 0.3 C. Such easily manufactured double-layer SCEs capable of operating steadily at room temperature provide a competitive electrolyte option for high-voltage solid-state LMBs.

show abstract

Interface engineering of Li1.3Al0.3Ti1.7(PO4)3 ceramic electrolyte via multifunctional interfacial layer for all-solid-state lithium batteries

Cited by 63 publications

References 37 publications

Sulfide and Oxide Inorganic Solid Electrolytes for All-Solid-State Li Batteries: A Review

Sulfide and Oxide Inorganic Solid Electrolytes for All-Solid-State Li Batteries: A Review

Progress and perspective of Li_1 + _xAl_xTi₂_‐x(PO₄)₃ ceramic electrolyte in lithium batteries

Double-Layer Solid Composite Electrolytes Enabling Improved Room-Temperature Cycling Performance for High-Voltage Lithium Metal Batteries

Contact Info

Product

Resources

About

Interface engineering of Li1.3Al0.3Ti1.7(PO4)3 ceramic electrolyte via multifunctional interfacial layer for all-solid-state lithium batteries

Cited by 63 publications

References 37 publications

Sulfide and Oxide Inorganic Solid Electrolytes for All-Solid-State Li Batteries: A Review

Sulfide and Oxide Inorganic Solid Electrolytes for All-Solid-State Li Batteries: A Review

Progress and perspective of Li1 + xAlxTi2‐x(PO4)3 ceramic electrolyte in lithium batteries

Double-Layer Solid Composite Electrolytes Enabling Improved Room-Temperature Cycling Performance for High-Voltage Lithium Metal Batteries

Contact Info

Product

Resources

About

Progress and perspective of Li_1 + _xAl_xTi₂_‐x(PO₄)₃ ceramic electrolyte in lithium batteries