Initial Design Considerations for a Cost Effective Treatment of Stripper Oil Well Produced Water

Adewumi, Michael A.; Erb, Justin; Watson, R.W.

doi:10.1007/978-1-4615-2902-6_40

Cited by 10 publications

(5 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Adewumi et al [48] proposed a three-step pretreatment before sand filtering for removing metals from produced water. The system consisted of the following:…”

Section: Sand Filtersmentioning

confidence: 99%

Review of technologies for oil and gas produced water treatment

Fakhru’l‐Razi

Pendashteh

Abdullah

et al. 2009

Journal of Hazardous Materials

1,731

765

View full text Add to dashboard Cite

Produced water is the largest waste stream generated in oil and gas industries. It is a mixture of different organic and inorganic compounds. Due to the increasing volume of waste all over the world in the current decade, the outcome and effect of discharging produced water on the environment has lately become a significant issue of environmental concern. Produced water is conventionally treated through different physical, chemical, and biological methods. In offshore platforms because of space constraints, compact physical and chemical systems are used. However, current technologies cannot remove small-suspended oil particles and dissolved elements. Besides, many chemical treatments, whose initial and/or running cost are high and produce hazardous sludge. In onshore facilities, biological pretreatment of oily wastewater can be a cost-effective and environmental friendly method. As high salt concentration and variations of influent characteristics have direct influence on the turbidity of the effluent, it is appropriate to incorporate a physical treatment, e.g., membrane to refine the final effluent. For these reasons, major research efforts in the future could focus on the optimization of current technologies and use of combined physico-chemical and/or biological treatment of produced water in order to comply with reuse and discharge limits.

show abstract

“…Adewumi et al [48] proposed a three-step pretreatment before sand filtering for removing metals from produced water. The system consisted of the following:…”

Section: Sand Filtersmentioning

confidence: 99%

Review of technologies for oil and gas produced water treatment

Fakhru’l‐Razi

Pendashteh

Abdullah

et al. 2009

Journal of Hazardous Materials

1,731

765

View full text Add to dashboard Cite

show abstract

“…Sand filtration is a technique to remove sand particles or other suspended particles from the produced residual water, and before sending to sand filtration the produced residual water needs to be adjusted in terms of pH, oxygen content as per Adewumi et al [29].…”

Section: Physical Treatmentsmentioning

confidence: 99%

Potential Use of Treated Produced Water in Irrigation: A Review

Suhane

Dewan

Mohaimin

2021

Advances in Sustainable Development

View full text Add to dashboard Cite

“…Adsorption as a treatment method was studied by Janks [10] using tailored zeolites. The Crudersorb technology that employed a series of adsorption steps was reported to reduce oil and grease content to less than 29 ppm [11]. Although frequently applied for particle extraction from water samples, the prominent drawback of the adsorption methods is the frequent regeneration of adsorbents and the waste generated.…”

Section: Produced Water Treatmentmentioning

confidence: 99%

“…Although frequently applied for particle extraction from water samples, the prominent drawback of the adsorption methods is the frequent regeneration of adsorbents and the waste generated. Adewumi [11] suggested the use of sand filtering preceded by a set of pretreatments for the efficient removal of metals from PW. While separators such as centrifuges and hydro-cyclones were industrially used for de-oiling PW, Van den Broek [12] hinted towards the low performance efficiency of the systems, also commenting on the inability of the methods to extract hazardous components, thus requiring other post treatment options.…”

Section: Produced Water Treatmentmentioning

confidence: 99%

Humidification–Dehumidification (HDH) Desalination and Other Volume Reduction Techniques for Produced Water Treatment

Khraisheh

Inamdar

Almomani

et al. 2021

Water

View full text Add to dashboard Cite

Volume reduction has been suggested as a novel method to tackle the various challenges associated with produced water. The present solution offers an economical and environmentally friendly solution to treat a large bulk of produced water that may overwhelm conventional water treatment methods. The current study provides a review of the various volume reduction technologies including freeze concentration, reverse osmosis, and humidification and dehumidification desalination systems. Focus is concentrated on the general HDH technologies in addition to its integration with refrigeration cycles for conditioned air production, and the power cycles for power generation. The GOR, freshwater yield, and efficiencies of the integrated HDH systems were reviewed. Lastly, innovation in the HDH desalination technology is discussed with emphasis on its incorporation with the MVC process.

show abstract

Initial Design Considerations for a Cost Effective Treatment of Stripper Oil Well Produced Water

Cited by 10 publications

References 1 publication

Review of technologies for oil and gas produced water treatment

Review of technologies for oil and gas produced water treatment

Potential Use of Treated Produced Water in Irrigation: A Review

Humidification–Dehumidification (HDH) Desalination and Other Volume Reduction Techniques for Produced Water Treatment

Contact Info

Product

Resources

About