Influence of reversion on adhesion in the rubber-to-metal vulcanization-bonding process

Souid, Anouar; Sarda, Alain; Deterre, Rémi; Leroy, Éric

doi:10.1016/j.polymertesting.2014.11.007

Cited by 10 publications

(4 citation statements)

References 9 publications

(13 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Various studies are performed on vulcanization bonding process for the manufacturing of rubber-to-metal bonded parts to reduce noise and vibrations of vehicles [4].In vulcanization bonding process, rubber metal parts have to be put in a vulcanization mold tool sizing the largest dimension of the parts which usually requires a big-sized mold with high costs [5].…”

Section: Introductionmentioning

confidence: 99%

Post-Bonding Application for Vehicle Antiroll Bars’ Rubber-Metal Bushes

2020

IJETER

View full text Add to dashboard Cite

In this presented study, major production parameters of the Post-Bonding method are changed systematically. Their effects on bonding strength are investigated and optimized experimentally. Using vulcanization as an example, it has been experimentally shown that the new post-bonding technology works as a production process. In study showed that the technique of subsequent bonding improves the quality and service life of parts in systems of antiroll bars. A new post-bonding application for adhesion of the rubbermetal parts was developed. The parameters of this technique were investigated and applied to rubber-metal couple adhesion of the automobile antiroll bar's bushes as a practical application Mechanical requirements of the rubber bushes were determined. adial stiffness measurements and tensile tests were performed to verify the optimized designs. The results were compared to evaluate outputs of the new post-bonding technique. As a result, the interactions of the parameters have been investigated to each other and better cases are selected. The technique was reduced to molding process in the long anti roll bar and rubber bushes to combining needs.

show abstract

Section: Introductionmentioning

confidence: 99%

Post-Bonding Application for Vehicle Antiroll Bars’ Rubber-Metal Bushes

2020

IJETER

View full text Add to dashboard Cite

show abstract

“…Moreover, with respect to the MCF rubber, the contact resistance must be reduced such that the adhesion between the electrodes and MCF rubber has higher sensitivity. This problem is related to the general research themes of adhesion between the metal and rubber [11,12,13,14,15,16,17] and the prevention of corrosion of the metal surface [18,19,20,21]. Hence, various methods of adhesion between the metal and rubber have been hitherto proposed.…”

Section: Introductionmentioning

confidence: 99%

Novel Adhesion Technique Using Metallic or Non-Metallic Hydrous Oxide of Metal Complexes Involving Magnetic Compound Fluid Rubber under Electrolytic Polymerization and Magnetic Field for Producing Sensors

Shimada

Kikura

Takahashi

et al. 2019

Sensors

View full text Add to dashboard Cite

As per sequential studies on new types of soft rubber for the artificial skin of robots, smart sensors, etc., we have proposed and investigated hybrid skin (H-Skin) and haptic sensors by using magnetic compound fluid (MCF), compounding natural rubber latex (NR-latex), and applying electric and magnetic fields. Through electrolytic polymerization, the MCF rubber is solidified. The MCF rubber has hybrid sensing functions and photovoltaic effects, and electric charge as battery. In case of the production of soft rubber sensors, however, the problem of adhesion between metal electrodes and rubber is very important. In the present study, we propose a novel adhesive technique for bonding the metal electrodes and MCF rubber by using metallic or non-metallic hydrous oxide, which is a metal complex, via electrolytic polymerization. The anionic radical hydrate reacts with the isoprene molecules of NR-latex or chloroprene rubber latex (CR-latex) such that they are cross-linked and the MCF rubber with the hydrate is solidified, which can be represented via a chemical reaction equation. By means of this adhesive technique, we presented five cases of sensors fabricated using metal electrodes and rubbers. This technique is applicable for novel cohesion between rubber and metal.

show abstract

“…3,4 The complexity of the vulcanization bonding process lies in the fact that the vulcanization of rubber and the curing of an adhesive previously coated onto solid adherend materials such as metal, cured resin, and rubber surfaces must occur simultaneously during a single molding step. 5 During this step, the uncured resin or rubber flows into the mold and contacts the adherend surface. In case of adhesive adhesion, the adhesive can also flow onto the surfaces of the adherend materials.…”

Section: Introductionmentioning

confidence: 99%

“…The adhesion between pairs of parts is indispensable in the fabrication of integration devices with high reliability . As an adhesion technology of polymers, adhesive adhesion and the vulcanization bonding process are used in a growing number of industrial applications. , The complexity of the vulcanization bonding process lies in the fact that the vulcanization of rubber and the curing of an adhesive previously coated onto solid adherend materials such as metal, cured resin, and rubber surfaces must occur simultaneously during a single molding step . During this step, the uncured resin or rubber flows into the mold and contacts the adherend surface.…”

Section: Introductionmentioning

confidence: 99%

Integration of Peroxide-Cured Rubber/Rubber Through Covalent Grafting of a Thiol-Linked Molecular Layer

Sang

Aisawa

Kudo³

et al. 2016

Ind. Eng. Chem. Res.

View full text Add to dashboard Cite

A simple, nonfluid, and direct adhesion method was developed to adhere cured rubber/rubber via grafting of a molecular layer of a triazine-based silane coupling agent without any pretreatment. During peroxide curing, oxide functional groups that can react with silanol groups were automatically fabricated on the surface of acrylonitrile–butadiene rubber (NBR) during primary processing at different curing temperatures. After the molecular layer was grafted onto the cured rubber surface, nonfluid adhesion between the cured NBR surfaces was induced. An NBR/NBR joined body was obtained and exhibited high adhesion strength with cohesive failure. The presented method is rapid, inexpensive, and environmentally friendly and can resolve the persistent problems of spew, extra adhesive, and rugose interface in the “fluid adhesion” of adhesive adhesion and vulcanization bonding processes. In addition, this method does not require secondary processing for inducing the formation of functional groups and should, therefore, be particularly valuable in industrial adhesion applications.

show abstract

Influence of reversion on adhesion in the rubber-to-metal vulcanization-bonding process

Cited by 10 publications

References 9 publications

Post-Bonding Application for Vehicle Antiroll Bars’ Rubber-Metal Bushes

Post-Bonding Application for Vehicle Antiroll Bars’ Rubber-Metal Bushes

Novel Adhesion Technique Using Metallic or Non-Metallic Hydrous Oxide of Metal Complexes Involving Magnetic Compound Fluid Rubber under Electrolytic Polymerization and Magnetic Field for Producing Sensors

Integration of Peroxide-Cured Rubber/Rubber Through Covalent Grafting of a Thiol-Linked Molecular Layer

Contact Info

Product

Resources

About