Influence of different hot-pressing conditions on the performance of eco-friendly jabon plywood bonded with citric acid adhesive

Sutiawan, Jajang; Hermawan, Dede; Massijaya, Muh Yusram; Kusumah, Sukma Surya; Marlina, Resti; Purnomo, Deni; Sulastiningsih, I M

doi:10.1080/17480272.2021.1884898

Cited by 21 publications

(22 citation statements)

References 42 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The density of Jabon wood after the densification is shown in Figure 1. The lowest Jabon wood density value was 0.39 g/cm 3 , and the highest Jabon wood density value was 0.42 g/cm 3 , obtained during a densification time of 10 minutes. The findings demonstrated that compared to control Jabon wood, which increased between 5.13% to 11.90%, the density value of densification Jabon wood with a densification ratio of 20% increased.…”

Section: Physical Propertiesmentioning

confidence: 86%

“…The average value of Jabon wood for the control value is 0.37 g/cm 3 , and after the densification process, it ranged from 0.39-0.42 g/cm 3 . The density of Jabon wood after the densification is shown in Figure 1.…”

Section: Physical Propertiesmentioning

confidence: 93%

“…Fast-growing wood species dominate the production of this log. Fast-growing trees are a particular kind of woody plant with a harvest time of fewer than 10 years [2][3][4][5][6][7] This kind of plant is widely grown in Industrial Plantation Forests (HTI) and Community Plantation Forests (HTR) due to its quick harvesting phase [5]. However, the standard essential features this fast-growing plant species has, such as its low-density value and low level of dimensional stability, provide issues in its application [8].…”

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

The effect of densification time on quality of Jabon Wood (Anthocephalus cadamba)

Hartono,

Sitompul,

Sutiawan

et al. 2023

IOP Conf. Ser.: Earth Environ. Sci.

View full text Add to dashboard Cite

Wood densification is a technique to increase the quality of low-density wood such as Jabon wood. The variation of densification time of Jabon wood will affect the quality of the wood. This study aimed to determine the effect of densification time on the physical and mechanical properties of Jabon wood. Jabon wood was densification using a hot press at 5, 10, 15, and 20 minutes at a temperature of 180 °C and a densification target of 20%. This densification wood will be compared to control wood. The results showed that the density value increased from 0.37 g/cm3 to 0.39-0.42 g/cm3, and the moisture content value was reduced to 11.57-15.12 %. There was an increase in value modulus of elasticity, modulus of rupture, and compression parallel to the grain by 31.55-48.86%, 6.65-35.33%, and 42.68-55.26%, respectively. The optimum value of this study resulted in a densification time of 10 minutes.

show abstract

Section: Physical Propertiesmentioning

confidence: 86%

Section: Physical Propertiesmentioning

confidence: 93%

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

The effect of densification time on quality of Jabon Wood (Anthocephalus cadamba)

Hartono,

Sitompul,

Sutiawan

et al. 2023

IOP Conf. Ser.: Earth Environ. Sci.

View full text Add to dashboard Cite

show abstract

“…The spectra were corrected for baseline using PerkinElmer software (Ver. 10.5.3, Perkin Elmer Inc., Hopkinton, MA, USA) [ 19 ].…”

Section: Methodsmentioning

confidence: 99%

“…The parameters of pressing temperature and time play an essential role in determining the rate of curing of the adhesive [ 19 ]. Muruganandam et al [ 20 ] stated that the temperature and time of the press depend on the type of raw material used and the product produced.…”

Section: Introductionmentioning

confidence: 99%

Properties of Table Tennis Blade from Sorghum Bagasse Particleboard Bonded with Maleic Acid Adhesive at Different Pressing Temperatures and Times

et al. 2022

Self Cite

View full text Add to dashboard Cite

This physical and mechanical properties of a table tennis blade made from sorghum bagasse particleboard (TTBSB-particleboard) bonded maleic acid adhesive was investigated under pressing temperature and time variations. The TTBSB-particleboard was produced via a two-stage process in this study. A pressing temperature of 170–200 °C was used to prepare the first stage for 10 min. Following this, the second stage of the TTBSB-particleboard was produced with a different pressing time of 5–20 min. The TTBSB-particleboard had a specified target density of 0.6 g/cm3 and a size of 30 cm × 30 cm × 0.6 cm, respectively. For references concerning the tested quality of TTBSB-particleboard, the JIS A 5908-2003 standard has been used. For comparison, the commercial blades of Yuguan Wooden 1011 and Donic Original Carbo Speed were tested under the same conditions. The quality of the TTBSB-particleboard was successfully enhanced by increasing the pressing temperature (170 to 200 °C) and time (5 to 20 min). As a result, the pressing condition of 200 °C and 20 min were effective in this study. The TTBSB-particleboard in this study has a greater weight than the commercial blades of Yuguan and Donic. However, the TTBSB-particleboard in this study had a ball rebound comparable to that of the Donic blade.

show abstract

Potential of Nanomaterials in Bio-Based Wood Adhesives: An Overview

Antov

Lee

Yadav

2022

Emerging Nanomaterials

View full text Add to dashboard Cite

Influence of different hot-pressing conditions on the performance of eco-friendly jabon plywood bonded with citric acid adhesive

Cited by 21 publications

References 42 publications

The effect of densification time on quality of Jabon Wood (Anthocephalus cadamba)

The effect of densification time on quality of Jabon Wood (Anthocephalus cadamba)

Properties of Table Tennis Blade from Sorghum Bagasse Particleboard Bonded with Maleic Acid Adhesive at Different Pressing Temperatures and Times

Potential of Nanomaterials in Bio-Based Wood Adhesives: An Overview

Contact Info

Product

Resources

About